Mercury 350 MAG MPI Horizon Скачать руководство пользователя | Manualshive

Страница: 56 / 74

background image

54

CC1014

1

CH48

Flushing Cooling System – 8.1 S Horizon Only

WARNING

When flushing, be certain the area around propeller is clear, and no one is standing nearby. To avoid
possible injury, remove propeller.

CAUTION

Do not run engine above 1500 rpm when flushing. Suction created by seawater pickup pump may col-
lapse flushing hose, causing engine to overheat.

CAUTION

Watch temperature gauge on dash to ensure that engine does not overheat.

CAUTION

If cooling system is to be flushed with boat in the water, water inlet valve (if equipped) must be closed,
or water inlet hose must be disconnected and plugged to prevent water from flowing into boat.

CAUTION

If boat is in the water, do not open water inlet valve until engine is to be restarted to prevent contami-
nated water from flowing back into engine.

NOTE: To prevent silt and/or salt buildup in cooling system, flush with freshwater at specified intervals.

1

Disconnect water inlet hose (upper hose) from aft end of seawater pickup pump. Using appropriate
connector, connect hose between connector and water tap.

2

Partially open water tap (about 1/2 maximum).

3

Place remote control in NEUTRAL, idle speed position, and start engine. Operate engine at idle speed, in
NEUTRAL, for about 10 minutes or until discharge water is clear.

4

Stop engine. Shut off water, remove flushing connector from pump inlet and reconnect water inlet hose.
Tighten hose clamp securely.

«
...
54
55
56
57
58
...
»

Содержание 350 MAG MPI Horizon











































































Отзывы:

Нет отзывов

Похожие инструкции для 350 MAG MPI Horizon

Бренд: VEM Страницы: 27

Бренд: VEM Страницы: 35

2.7-litre V6 Biturbo

Бренд: Audi Страницы: 72

Бренд: Briggs & Stratton Страницы: 12

Бренд: Petter Страницы: 58

Бренд: Central Machinery Страницы: 30

Бренд: Clarke Страницы: 41

Бренд: Arrow Shark Страницы: 16

Бренд: Briggs & Stratton Страницы: 60

Бренд: Toro Страницы: 27

Бренд: Volvo Penta Страницы: 114

Бренд: Optec Страницы: 10

Бренд: Honda Страницы: 31

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 2

O.S.MOTOR OMH-5830-490

Бренд: O.S. engine Страницы: 2

O.S.MOTOR OMA-2820-950

Бренд: O.S. engine Страницы: 2

MAX-46FX-Hring Series

Бренд: O.S. engine Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды