Mercury 240 Jet Drive Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 9

Mercury 240 Jet Drive Скачать руководство пользователя страница 9

MAINTENANCE

90-884822 DECEMBER 2001

Page 1B-9

h. Turn the engine off. Turn the water off if using a flushing attachment. Allow the water

to drain out of the unit completely.

i.

Complete the other recommended items for storage.

Protecting Jet Pump Components

IMPORTANT: Check and refill housing with Premium Gear Lubricant before storage
to protect against possible water leakage into housing which is caused by loose lu-
bricant vent or fill plug. Inspect gaskets under lubricant vent and fill plugs replacing
any damaged gaskets before reinstalling plugs.

1. Drain and refill drive housing unit and stator assembly with Premium Gear Lubricant as

explained in “Jet Pump” section (see Table of Contents).

2. Lubricate all lubrication points.

Battery Storage

1. Remove battery as soon as possible and remove all grease, sulfate and dirt from top

surface.

2. Cover plates with distilled water, but not over 3/16 in. (5 mm) above perforated baffles.

3. Cover terminal bolts well with grease.

4. Store battery in a cool, dry place in a dry carton or box.

5. Remove battery from storage every 60 days. Check water level and place on charge for

5 to 6 hours at 6 amperes. DO NOT fast charge.

CAUTION

A discharged battery can be damaged by freezing.

«
...
7
8
9

Содержание 240 Jet Drive










Отзывы:

Нет отзывов