Mercury 225 Sport XS OptiMax Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 96

background image

FEATURES AND CONTROLS

42

• The term trim generally refers to the adjustment of the outboard within

the first 20° range of travel.

• The term tilt generally refers to adjusting the outboard further up out

of the water or beyond the transom bracket support.

With the engine turned off, the outboard can be tilted out of the water. At

low idle speed, the outboard can also be tilted up past the trim range to

permit, for example, shallow water operation.

Power Trim Operation

With most boats, operating around the middle of the trim range will give

satisfactory results. Trimming your outboard all the way in or out may

improve performance, but cause some potential control hazards.

!

WARNING

Avoid possible serious injury or death. When the outboard is trimmed in

or out beyond a neutral steering condition, a pull on the steering wheel

in either direction may result. Failure to keep a continuous firm grip on

the steering wheel when this condition exists can result in loss of boat

control as the outboard can turn freely. The boat can now spin out or go

into a very tight maximum turn which, if unexpected, can result in

occupants being thrown within the boat or out of the boat.

Consider the following lists carefully.
Trimming in/down can:

• Lower the bow of the boat.
• Result in quicker planing off.
• Generally improve the ride in choppy water.
• Increase steering torque or pull to the right (with the normal right‑hand

rotation propeller).

• In excess, lower the bow to a point at which the boat begins to plow

with the bow in the water while on plane. This can result in an

unexpected turn in either direction called bow steering or over steering

if any turn is attempted, or if a significant wave is encountered.

Trimming out/up can:

• Lift the bow higher out of the water.
• Generally increase top speed.
• Gain clearance over submerged objects or a shallow bottom.
• Increase steering torque or pull to the left at a normal installation

height (with the normal right hand rotation propeller).

«
...
48
49
50
51
52
...
»

Содержание 225 Sport XS OptiMax

































































































Отзывы:

Нет отзывов

Похожие инструкции для 225 Sport XS OptiMax

Бренд: ASRock Industrial Страницы: 44

Бренд: AOpen Страницы: 8

Бренд: Texas Instruments Страницы: 19

Kontron mITX-CFL-S

Бренд: S&T Страницы: 8

Бренд: JETWAY Страницы: 56

Бренд: Wintech Страницы: 5

Бренд: Quantum Design Страницы: 77

A320M-K PRO V14

Бренд: Colorful Страницы: 12

Бренд: Global American Страницы: 37

Бренд: Gigabyte Страницы: 93

975X Platinum Series

Бренд: MSI Страницы: 157

Бренд: Telit Wireless Solutions Страницы: 47

Бренд: ASROCK Страницы: 160

Бренд: AOpen Страницы: 11

Бренд: Seco Страницы: 49

Бренд: Norco Страницы: 55

Бренд: Gigabyte Страницы: 88

Бренд: MSI Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды