Mercury 2004 Sable Скачать руководство пользователя страница 109

Страница: 109 / 249

crash severity are appropriate to activate these devices. Refer to the

Personal Safety System

section in this chapter.

Important supplemental restraint system precautions

Air bags DO NOT inflate slowly or
gently and the risk of injury from a
deploying air bag is greatest close to
the trim covering the air bag
module.

All occupants of the vehicle, including the driver, should always
properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

Always transport children 12 years old and under in the back
seat and always properly use appropriate child restraints.

National Highway Traffic Safety Administration (NHTSA)
recommends a minimum distance of at least 25 cm (10 inches)

between an occupant’s chest and the driver air bag module.

Never place your arm over the air bag module as a deploying air
bag can result in serious arm fractures or other injuries.

Steps you can take to properly position yourself away from the airbag:

•

Move your seat to the rear as far as you can while still reaching the
pedals comfortably.

•

Recline the seat slightly (one or two degrees) from the upright
position.

2004 Sable

(sab)

Owners Guide (post-2002-fmt)
USA English

(fus)

Seating and Safety Restraints

108

Содержание 2004 Sable


























































































































































































































































Результаты поиска

Содержание 2004 Sable

Отзывы:

Бренды по названию

Популярные бренды

Mercury 2004 Sable, Руководство пользователя

Результаты поиска

Содержание 2004 Sable

Отзывы:

Бренды по названию

Популярные бренды