MerCruiser Axius 350 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 149

background image

Section 5 - Maintenance

Page 90

90-8M0053363

eng

NOVEMBER 2010

NOTE: Add coolant only when engine is at normal operating temperature.

1. Remove the fill cap from the coolant recovery bottle.
2. Fill to the "FULL" line with the specified coolant.

Tube Ref No.

Description

Where Used

Part No.

122

Extended Life Antifreeze/

Coolant

Closed Cooling System

92-877770K1

3. Install the fill cap onto the coolant recovery bottle.

Changing

Contact your authorized Mercury MerCruiser dealer.

Sterndrive Gear Lube

Checking

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

NOTE: The level of gear lube oil will fluctuate during operation. Check the oil level with the engine cold, before starting.

1. Check the gear lube level in the gear lube monitor. Keep the level within the recommended operating range.

a -

Gear lube monitor

b -

Typical closed cooled

model

c -

Typical seawater cooled

model

2. Inspect the lubricant condition. If any water is visible at the bottom of the gear lube monitor, if water appears at the fill and

drain plug hole, or if the gear lube appears discolored, contact your authorized Mercury MerCruiser dealer immediately. These

conditions can indicate a water leak in the sterndrive.

Filling

IMPORTANT: If more than 59 mL (2 fl oz) of High Performance Gear Lubricant is required to fill the monitor, a seal may be leaking.

Damage to the sterndrive unit may occur due to lack of lubrication. Contact your authorized Mercury MerCruiser dealer.
1. Remove the gear lube monitor cap.
2. Fill the monitor with the specified fluid so that the level is in the operating range. Do not overfill.

Shown removed for visual clarity

a -

Gear lube monitor cap

b -

Operating range (full) line

a

32539

a

b

c

b

a

7884

«
...
96
97
98
99
100
...
»

Содержание Axius 350






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Axius 350

Neomat A Series

Бренд: Nice Страницы: 52

Бренд: Saito Страницы: 4

Бренд: Hoval Страницы: 12

Бренд: Interpump Страницы: 16

Бренд: Black Bruin Страницы: 70

Бренд: Lycoming Страницы: 38

Бренд: FIAMA Страницы: 7

Бренд: Powertrain Страницы: 36

Stagemaker SM10

Бренд: R & M Страницы: 71

max-18tz series

Бренд: O.S. engine Страницы: 25

Бренд: Honda Страницы: 431

Бренд: NACIONAL MOTOR Страницы: 72

Бренд: Milwaukee Страницы: 43

Бренд: Milwaukee Страницы: 54

Бренд: Marinediesel Страницы: 248

Бренд: TOHATSU Страницы: 89

Бренд: Zenoah Страницы: 28

Global TEFC Series

Бренд: Baldor Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды