MerCruiser Axius 350 Скачать руководство пользователя страница 47

Страница: 47 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 39

•

Generally increases speed and engine RPM

•

Causes bow to bounce in choppy water

•

Increases danger of following wave splashing into the boat when coming off plane

•

At extremes, can cause the boat to porpoise

Shifting weight to front (bow):
•

Improves ease of planing

•

Improves rough water ride

•

At extremes, can cause the boat to veer back and forth (bow steer)

The Bottom of the Boat

To maintain maximum speed, the boat bottom should be:
•

Clean, free of barnacles and marine growth

•

Free of distortion; nearly flat where it contacts the water

•

Straight and smooth, fore and aft

Marine vegetation may accumulate when the boat is docked. This growth must be removed before operation; it may clog the water

inlets and cause the engine to overheat.

Cavitation

Cavitation occurs when water flow cannot follow the contour of a fast‑moving underwater object, such as a gear housing or a

propeller. Cavitation increases propeller speed while reducing boat speed. Cavitation can seriously erode the surface of the gear

housing or the propeller. Common causes of cavitation are:
•

Weeds or other debris snagged on the propeller

•

Bent propeller blade

•

Raised burrs or sharp edges on the propeller

Ventilation

Ventilation is caused by surface air or exhaust gases that are introduced around the propeller resulting in propeller speed‑up and

a reduction in boat speed. Air bubbles strike the propeller blade and cause erosion of the blade surface. If allowed to continue,

eventual blade failure (breakage) will occur. Excessive ventilation is usually caused by:
•

Drive unit trimmed out too far

•

A missing propeller diffuser ring

•

A damaged propeller or gear housing, which allows exhaust gases to escape between propeller and gear housing

•

Drive unit installed too high on transom

Elevation and Climate

Elevation and climate changes will affect the performance of your power package. Loss of performance can be caused by:
•

Higher elevations

•

Higher temperatures

•

Low barometric pressures

•

High humidity

For you to have optimum engine performance under changing weather conditions, it is essential that the engine be propped to

allow the engine to operate at or near the top end of the specified maximum RPM range with a normal boat load during your normal

boating weather conditions.
In most cases, recommended RPM can be achieved by changing to a lower pitch propeller.

Propeller Selection

IMPORTANT: The engines covered in this manual are equipped with an RPM rev‑limiter that is set to an upper RPM limit. This

limit, which is slightly above the normal operating range of the engine, helps prevent damage from excessive engine RPM. Once

the RPM returns to the recommended operating RPM range, normal engine operation resumes.
The boat manufacturer and the selling dealer are responsible for equipping the power package with the correct propeller. Refer

to Mercury Marine's web page

http://www.mercurymarine.com/everything_you_need_to_know_about_propellers6

Select a propeller that will allow the engine power package to operate at or near the top end of the recommended WOT operating

RPM range with a normal load.

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды