MerCruiser Axius 350 Скачать руководство пользователя страница 45

Страница: 45 / 149

Section 3 - On The Water

90-8M0053363

eng

NOVEMBER 2010

Page 37

Boats Having an Open Front Deck

No one should ever be on the deck in front of the fence while the boat is in motion. Keep all passengers behind the front fence or

enclosure.
Persons on the front deck could easily be thrown overboard or persons dangling their feet over the front edge could get their legs

caught by a wave and pulled into the water.

mc79555-1

WARNING

Sitting or standing in an area of the boat not designed for passengers at speeds above idle can cause serious injury or death.

Stay back from the front end of deck boats or raised platforms and remain seated while the boat is in motion.

Boats With Front-Mounted, Raised Pedestal Fishing Seats

Elevated fishing seats are not intended for use when the boat is traveling faster than idle or trolling speed. Sit only in seats

designated for traveling at faster speeds.
Any unexpected, sudden reduction in boat speed could result in the elevated passenger falling over the front of the boat.

mc79557-1

Wave and Wake Jumping

WARNING

Wave or wake jumping can cause serious injury or death from occupants being thrown within or out of the boat. Avoid wave or

wake jumping whenever possible.

mc79680-1

Operating recreational boats over waves and wakes is a natural part of boating. However, when this activity is done with enough

speed to force the boat hull partially or completely out of the water, certain hazards arise, particularly when the boat re‑enters the

water.
The primary concern is the boat changing direction while in the midst of the jump. In such cases the landing may cause the boat

to violently veer in a new direction. Such a sharp change in direction or turn can cause occupants to be thrown out of their seats

or out of the boat.
There is another less common hazardous result from allowing your boat to launch off of a wave or wake. If the bow of your boat

pitches down far enough while airborne, upon water contact it may penetrate under the water surface and submarine for an instant.

This will bring the boat nearly to a stop in an instant and can send the occupants flying forward. The boat may also veer sharply

to one side.

Содержание Axius 350






















































































































































Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды

MerCruiser Axius 350, Инструкция по эксплуатации

Результаты поиска

Содержание Axius 350

Отзывы:

Похожие инструкции для Axius 350

Бренды по названию

Популярные бренды