background image

Please retain product label and instructions for future reference

           

Step 5

Parts needed -              & 

Place the Ridge Bar 

(No. 11)

 in between  

the Door Gable 

(No. 1) 

and Plain Gable 

(No. 4)

. Ensure the top  corners of the 

Ridge Bar 

(No. 11) 

are flush with  each 

top point (see illustration). 

Secure in place using a L bracket 

(No.18)

 on each end and 4x30mm 

screws per brace.

8x30mm screws

 

30mm 

screw

18

18

18

11

1!

2!

Pre drill 

hole

11

Step 6

Parts needed -             &

Fix an Eaves Frame 

(No. 14)

 to each 

roof OSB sheet using 3x30mm screws 

per eave.

Fix the Roof sheets 

(No. 5)

 to the roof  

ensuring they come together at the 

top using 12x40mm screws per sheet, 

directly through the roof sheet at the 

top. Make sure to attach the roofs to 

the ridge bar. 

6x30mm screws

24x40mm screws

40mm 

screw

30mm 

screw

5

5

14

1!

2!

Pre drill 

hole

14

5

Step 7

Parts needed -       

Fit the Fascia Block 

(No. 15)

 to the front of 

the building using 4x30mm screws, make 

sure it is flush with the outside edge of 

each roof OSB sheet 

(No. 5)

.

4x30mm screws

30mm 

screw

1!

2!

Pre drill 

hole

15

15

1!

2!

Pre drill 

hole

Step 8

      

Once the roof 

(No.5

) is fixed, secure the 

building to the Floor 

(No.6) 

using 

5x50mm screws per panel, making sure 

to screw into the Floor bearers.

20x50mm screws

50mm 

screw

b

b

b

b

b

b

b

b

b

b

b

Please retain product label and instructions for future reference

             

DO NOT ALLOW YOUR CHILD TO PLAY WITH ANY 

COMPONENT PARTS PRIOR  TO ASSEMBLY.

www.merciagardenproducts.co.uk      P6

Содержание SI-002-001-0022













Отзывы: