Mercia Garden Products 01DTOVPN0705SDFW-V1, Общее руководство по инструкции

Страница: 4 / 9

P 4
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air flow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be affected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproofing treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual treatment.
Ensure the base is level and is built on firm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run off for water. It is also recommended that the floor be at least 25mm above
the surrounding ground level to avoid flooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
Please retain product label and instructions for future reference
Place the Plain panel 1
(No.5)
and the Left
Gable (No.4) onto the floor. Fix the corners
with 50mm screws as shown in diagram.
Do not secure the building to the floor
until the roof is fitted
.
3x50mm Screws
Pre drill
hole
50mm
screw
a
a
4
5
Step 3
Parts Needed - No.4 QTY 1
- No.5 QTY 1
a
a
Place the Plain panel 2 (No.6) onto the
floor along side the Plain Panel 1. Fix
along the end of the panels in alternating
pattern using 3x50mm Screws.
Place the Window Panel (No.2) onto the
floor. Fix the corner of the Left Gable with
3x50mm screws as shown in diagram.
Do not secure the building to the floor
until the roof is fitted.
6x50mm Screws
Pre drill
hole
50mm
screw
Step 4
Parts Needed - No.2 QTY 1
- No.6 QTY 1
2
6
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
1
3
Pre drill
hole
50mm
screw
Step 5
Parts Needed - No.1 QTY 1
- No.3 QTY 1
a
Place the Right Gable (No.3) and the
Door Panel
(No.1)
onto the floor. Fix
the Panels together with 3x50mm
screws at each join as shown in
diagram.
Do not secure the building to the
floor until the roof is fitted.
9x50mm Screws
8x20mm Screws
Place the ridge bar
(No.10)
in between the
two gables. Ensure the top corner of the
ridge bar sit flush with the top of the gable.
Fix the ridge bar to the gable using one L
bracket
(No.23)
for each end and Fix with
4x20mm screws each.
23
20mm
screw
Pre drill
hole
10
Step 6
Parts Needed - No.10 QTY 1
- No.23 QTY 2
**Please note: the front panels
are interchangable and can be
positioned on either side of the
building. Decide which works
best before assembly**