04
1 Initial setup required.
01 Fuel gauge
02 Clock
03 Speedometer with Multifunction display
04 Tachometer
05 Coolant Temperature gauge
01 Multifunction display
02 Call Functions
03 Volume Controls
04 Menu Controls
01 Window Controls
02 Mirror adjustment
03 headlamp Switch
04 garage door opener
1
05 Multifunction display
06 Cd/dVd Changer
07 CoMand display
08 automatic Climate Control
09 overhead Control Panel
dRiVeR'S VieW
inSTRUMenT CLUSTeR & MULTiFUnCTion STeeRing WheeL
SeaT adjUSTMenT & SeaT MeMoRY
adjUSTMenT STaLKS
LighTing
geaR SeLeCToR
To adjUST SeaT PoSiTion
01 Seat forward/back
02 Backrest tilt
03 Seat height
04 Leg support
05 headrest height
To adjUST CRUiSe ConTRoL
01 Push lever up to activate
Push lever up to accelerate
02 Push lever down to decelerate
03 Push lever as shown to cancel
04 Pull lever as shown to recall last
cruise control setting
CoRneR-iLLUMinaTing LaMPS
The corner-illuminating lamps will
automatically turn on when you activate
the turn signal at a certain speed and the
steering wheel is turned
The corner-illuminating lamps will then
illuminate the area in which you
are turning
geaR SeLeCToR PoSiTion
01 The gear selector position currently in use
is displayed in the multifunction display
noTe: Please see all applicable
information and adhere to the warnings
in the operator’s Manual.
While in drive, you can also manually
shift through the gears by pressing the
shift paddles (if equipped) behind the
steering wheel on the left (downshift) or
right (upshift)
headLaMP SWiTCh PoSiTionS
01 Standing lamps left mode
This position will activate the driver side
standing lamps
02 Standing lamps right
This position will activate the passenger
side standing lamps
noTe: The standing lamp feature is
helpful at night to alert other motorists
of your vehicle.
03 off / daytime running lamp mode
When you switch off the vehicle
the headlights are turned off
When daytime running lamp mode is
activated, the headlamps are turned
on when the ignition is switched on
04 automatic headlamp mode
This position automatically turns
on the headlamps in certain
lighting conditions
This function is deactivated in daytime
running lamp mode
05 Parking lamps mode
The parking lamps on both sides of
the vehicle are activated
This position is only suggested for
short stops
06 Low beam mode
The low beam headlamp position is
the standard position for driving with
headlamps turned on
07 Front fog lamps
in position 06 pull on the switch once
to turn on the front fog lamps
08 Rear fog lamps
in position 05 or 06 pull on the switch
twice to turn on the rear fog lamps
P Park
When leaving the vehicle also apply the
parking brake and, on inclines, turn the
wheels toward the curb
R Reverse
Place the gear selector lever in reverse
only when the vehicle is stopped
n neutral
The neutral position is used when towing
the vehicle or when using a conveyor type
car wash
d drive
This position is the standard
driving position
SWiTChing geaRS
The gear selector lever allows you
to chose the transmission setting of
the vehicle
The vehicle can only be started while in
park (position P) or neutral (position n)
To move the selector lever out of park,
the ignition must be switched on and you
must step firmly on the brake pedal
To adjUST STeeRing WheeL PoSiTion
01 To extend or retract the steering wheel
move stalk forward or back
02 To raise or lower the steering wheel move
the stalk up or down
To adjUST WindShieLd WiPeR SeTTingS
01 Rotate windshield wiper switch
counter-clockwise to 1 of 4 settings
0
off position
Slow intermittent wiping
Faster intermittent wiping
Constant slow wiping
Constant fast wiping
noTe: The rain sensor in the windshield
controls the intermittent wiping settings.
02
You can press on the tip of the
adjustment stalk once to wipe
with washer fluid
SToRing PoSiTionS inTo MeMoRY
adjust the seat to the desired position
on the driver’s side adjust the steering
wheel and the exterior rear view mirrors
Press memory button "M"
Release memory button "M" and press one
of the memory position buttons within
3 seconds
To recall a previously saved position
simply press and hold the memory
position button
noTe: all the settings are stored with the
selected position. To recall a previously
saved position simply press the memory
position button (1, 2, or 3).
LUMBaR SUPPoRT adjUSTMenT & eXTeRioR MiRRoR adjUSTMenT
To adjUST oUTSide MiRRoRS
Switch on the ignition
Select the mirror to be adjusted
01 driver side mirror
02 Passenger side mirror
adjust the mirror to desired position
using button 03
To adjUST LUMBaR (lower back) SUPPoRT
adjust lever back and forth until you are
comfortable with the adjustment
03
06
05
08
09
07
04
03
03
03
03
04
A
A
C
B
B
C
04
04
01
05
01
01
02
01
02
02
02
01
01
03
04
05
02
02
04
01
08
02
02
04
03
03
05
06
07
01
01
01
02
02
