Control panel, manoeuvring the chair
Brake release
Disengaging the brake enables the chair to be moved manually. Turn the manoeuvre plate (1)
on both wheels a quarter turn anti-clockwise to disengage the brakes. If it is difficult to turn the
manoeuvre plate, try moving the chair backwards and forwards a little. To re-engage the brakes,
turn the plate (1) on both wheels a quarter turn clockwise and roll the chair carefully until the
brakes are engaged with an audible "click". NB: On no account must the main switch be on
when the brakes are disengaged. The brakes must never be engaged using the motor. The chair
must never be transported with the brakes disengaged.
1
Manoeuvring Driving
Turn on power switch (1). Check battery level (4). The battery level should not be down in the
red area. (see “charging”)
Driving: Check that the function display (3) shows number 2 (normal speed) or 1 (low speed). If
not, press function button (2) until one of the numbers is shown. Push joystick (5) straight ahead
for forward motion and diagonally forward left/right to turn. The chair can be spun around by
pushing the joystick (5) straight left/right. To back up, pull the joystick (5) back.
Manoeuvring Seating Unit:
For raising/lowering the seating unit or adjusting the electric seating angle/back angle or leg
support angle. Press option button (6). The electrical functions that are mounted on the chair
light up on the option display (7); the active electrical function blinks. Push joystick right/left
to switch between symbols on the option display and forward/backwards for manoeuvring the
various options.
(Symbol ) steers raising/lowering chair, (Symbol ) seating angle, (Symbol ) back angle
and (Symbol ) (Symbol ) for left/right leg support angle. The two leg support angles can be
manoeuvred simultaneously when both (Symbol ) (Symbol ) for left/right leg support angling
blink at the same time. When the chair’s electrical function is not used for five minutes, it shuts
off automatically in order to save battery capacity.
In order to start the electronics, press power switch (1) or touch the joystick (5). The time interval
for turning off is adjustable.
Signal horn: Press button (8).
Locking function: Use the magnetic key (9) in order to lock the electronics. The electronics must
be turned on with the power switch (1) when locking/unlocking. The magnetic key (9) is held
against the key symbol (10) for locking/unlocking. When locking, the manoeuvre panel turns off
completely, and the key symbol light blinks red; in order to unlock, the power switch (1) must be
turned on. When the chair is locked (and turned on), the red key symbol (10) lamp blinks; re-do
the procedure with the magnetic key (9).
The buttons (11) have not been programmed for any function.
9
Seat angle adjustment
Handle control
Gas spring
2
3
4
1
4
There are three alternative designs for adjusting
the angle of the seat: manual, gas spring and
handle control. Manual adjustment is done by
loosening the knob (1) beneath the seat. Adjust
to the position required and then lock the knob.
Please note! This knob should always be locked
when the chair is in use. The control for the gas
spring is situated at the back left-hand edge of
the seat (2) and is manoeuvred by pushing the
lever forward carefully. The controls may also be
placed under one of the armrests (3). The handle
device is manoeuvred using the handle (4).
REAL 6100
R
The REAL chair combines exchangeable components, accessories and func-
tions, with adjustability to your individual requirements. The chair is only to be
used by the person and for the purpose intended. The chair is designed for
indoor use only and should not be exposed to water, other liquids or chemicals.
It should not be exposed to high temperatures or long periods of intensive
sunlight or other radiation. The chair shall not be fitted with accessories or com-
ponents other than those approved by Mercado Medic AB. Repairs and other
technical measures may only be carried out by personnel authorised by Mer-
cado Medic AB. Please read the instructions carefully before using the chair.
INSTRUCTIONS for USE and CARE
Armrests
Articleno: 801974
April 2006
The armrests can be adjusted for height and width and can be folded back. The height is adjusted
with knob (1). To lower the armrest, unscrew the knob. To raise, life the armrest to the required
height and then lock in place with the knob. The width is adjusted using knob (2). Loosen
the knob, adjust and lock. Use knob (3) to fold the armrests back. Pull out and fold back. The
mechanism locks into position automatically when the armrests are folded back into an upright
position. It is possible to override the automatic locking by turning knob (3) a quarter turn.
Electrically powered wheelchair for indoor use for people with reduced functionality in the neck/back, in the legs and arms
1
2
3
Back rest
There are three types of back mechanisms: Standard, Medic and Comfort. The backrest is available in both a low
and a high design (all the chairs illustrated show the high backrest design). All back mechanisms have separate
adjustment controls for height (1) and angle (2). Loosen the knob, adjust to the desired height/angle and then lock
the knob. On the Comfort model with a gas spring device, push the lever forward to change the angle. On the
Medic model the depth can be adjusted by using the knob (3). In the high position the angle of the backrest itself
can be adjusted by using the knob. (4).
1
3
2
4
4
4
2
1
2
Standard
Comfort
Medic
1
2
11
8
6
7
10
4
5
1
2
3
Importan t information
REAL 6100 belongs to class A and is only to be used indoors
Max user weight: 130 kg.
REAL 6100 is tried and approves according to the EMC-directive.
Cell phones do not compromise the REAL 6100 driving quality.
REAL 6100 can influence electromagnetic fields.
2
2
2
2
2
2
2
