manualshive.com logo in svg

Memotec NetPerformer SDM-9120 Series, Руководство по установке оборудования

Поделиться
Скачать
Memotec NetPerformer SDM-9120 Series Скачать руководство пользователя страница 94

NetPerformer Hardware Installation Guide

4-26

 Memotec Inc. 

4.12.3

Converting an SDM-92x0 Card to an SDM-9120 Low-Profile

1.

Remove the SDM-92x0 type faceplate from the interface card by unscrewing the two 
screws securing that faceplate to the interface card.

2.

On the SDM-9120 type low-profile faceplate, secure the L-shaped mounting brackets 
using the bolts provided with the faceplate kit. Make sure that you put the brackets in 
their correct positions as illustrated in 

Figure 4-20

 below.

3.

Secure the assembled SDM-9120 type faceplate to the interface card by screwing 
back the two screws used to fix the faceplate to the interface card as illustrated in 

Figure 4-20

 below.

The ordering part numbers for the replacement faceplate kits from SDM-92x0 to SDM-
9120 are as follows:

• KT-0021210

: SDM-9120 Replacement Faceplate Kit for Quad E&M

• KT-0021208

: SDM-9120 Replacement Faceplate Kit for Dual FXO

• KT-0021206

: SDM-9120 Replacement Faceplate Kit for Quad FXO

• KT-0021204

: SDM-9120 Replacement Faceplate Kit for Dual FXS

• KT-0021202

: SDM-9120 Replacement Faceplate Kit for Quad FXS

• KT-0021200

: SDM-9120 Replacement Faceplate Kit for Single E1/T1

• KT-0021198

: SDM-9120 Replacement Faceplate Kit for Dual E1/T1

Figure 4-20:   SDM-9120 Interface Card Faceplate

Faceplate screws

Faceplate bolts

Left side L-shaped 
mounting bracket

Right side L-shaped 
mounting bracket

Содержание NetPerformer SDM-9120 Series


































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды