Meltem M-WRG-S/Z-24 Скачать руководство пользователя страница 2

Страница: 2 / 32

Installation manual

M-WRG-S/Z-S, M-WRG-S/Z-24,

M-WRG-S/Z-EIB, M-WRG-S/Z-KNX (-F, -FC)

- 2 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N & H E AT R E C O V E R Y

Contents

1 Introduction

..................................................................................................................... 5

1.1

Notes on this installation manual ...................................................................................... 5

1.2 Description

........................................................................................................................ 5

1.3

Target group ..................................................................................................................... 5

1.4

Revision index .................................................................................................................. 6

1.5

Explanation of the symbols used ...................................................................................... 6

1.6

Supplementary documents ............................................................................................... 6

Safety instructions ......................................................................................................... 6

2.1

Hazard classification

......................................................................................................... 6

2.2

Notes on using the ventilation units safely ....................................................................... 7

2.3

Intended use ..................................................................................................................... 7

Warranty and liability ..................................................................................................... 7

Tools and equipment required ...................................................................................... 7

Codes for designation of wire colours ......................................................................... 7

Connecting the M-WRG-S/Z-S to the control cable ..................................................... 8

6.1

Overview of the modules .................................................................................................. 8

6.1.1 Board in M-WRG-S/Z-S ventilation unit ............................................................................ 8

6.1.2 Three-step rotary switch with zero position ...................................................................... 8

6.1.3 Optional pushbutton for intensive ventilation and optional LED for feedback .................. 8

6.2

Control cable types ........................................................................................................... 9

6.3

Connecting the control cable to the ventilation unit .......................................................... 9

6.3.1 Removing the cover from the ventilation unit ................................................................... 9

6.3.2 Removing the network connection cover .......................................................................... 9

6.3.3 Connecting the control cable and optional pushbutton/LED to the ventilation unit

boards ............................................................................................................................. 10

6.3.3.1 Terminal assignment ....................................................................................................... 10

6.3.3.2 Circuit diagram ................................................................................................................ 11

6.3.4 Inserting the network connection cover and attaching the cover to the ventilation unit .. 12

Connecting the M-WRG-S/Z-24 to the control cable ................................................. 13

7.1

Overview of the modules ................................................................................................ 13

7.1.1 Board in M-WRG-S/Z-24 ventilation unit ........................................................................ 13

7.2

Control cable types ......................................................................................................... 13

7.3

Connecting the control cable to the ventilation unit ........................................................ 13

7.3.1 Removing the cover from the ventilation unit and removing the network connection

cover ............................................................................................................................... 13

7.3.2 Connecting the control cable to the ventilation unit board .............................................. 14

7.3.2.1 Input assignment (BCD encoding) .................................................................................. 14

7.3.2.2 Output assignment ......................................................................................................... 14

7.3.2.3 Circuit diagram ............................................................................................................... 15

7.3.3 Inserting the network connection cover and attaching the cover to the ventilation unit .. 15

Connecting the M-WRG-S/Z-EIB to the EIB universal interface 6119/40 and EIB

bus cable ....................................................................................................................... 16

8.1

Overview of the modules ................................................................................................ 16

Содержание M-WRG-S/Z-24

































Результаты поиска

Содержание M-WRG-S/Z-24

Отзывы:

Похожие инструкции для M-WRG-S/Z-24

Бренды по названию

Популярные бренды

Meltem M-WRG-S/Z-24, Руководство по установке

Результаты поиска

Содержание M-WRG-S/Z-24

Отзывы:

Похожие инструкции для M-WRG-S/Z-24

Бренды по названию

Популярные бренды