manualshive.com logo in svg

Meltem M-WRG-II Series, Инструкция по разборке, Страница: 6 / 14

Поделиться
Скачать
Meltem M-WRG-II Series Скачать руководство пользователя страница 6

Dismantling instructions 

Ventilation units from the M-WRG-II series

- 6 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

info@meltem.com · www.meltem.com

VENTILATION  THE  RIGHT WAY

V E N T I L A T I O N   &   H E A T   R E C O V E R Y

4.2 

Remove the unit cover

Fig. 1: 

Removing the cover from the ventilation unit

1

1

2

 

►

Using both thumbs, press the two latches 

(item 1 in Fig. 1) on the bottom of the venti-

lation unit. The unit cover (item 2 in Fig. 1) 

will come away.

 

► At the same time, push your index fingers 

into the gap between the unit cover and 

housing, and lift the unit cover up and away 

from the housing.

 

►

Pull away the black insulation on the back of 

the unit cover.

4.3 

Remove the air filters

Fig. 2:  Remove the air filters

1

2

 

► Using the hand grip, turn the filter ring 

(item 1 in Fig. 2) anti-clockwise until the filter 

ring is released from the retainers.

 

► Pull the filter ring together with the extract air 

filter out of the ventilation unit.

 

► Using the hand grip, turn the filter cover 

(item 2 in Fig. 2) anti-clockwise until the filter 

cover is released from the retainers.

 

► Pull the filter cover together with the outdoor 

air filter out of the ventilation unit.

Содержание M-WRG-II Series















Отзывы:

Нет отзывов