Meltem M-WRG-II E-F Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 60

background image

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 40 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

12.3.7 Resetting the filter change indicator

After every air filter change, the filter change indicator must be reset in order to restart

monitoring of the period since the last air filter change. The procedure is as follows:

► Press key 1 (item 1 in Fig. 12 on page 23) for roughly 5 seconds.

The ventilation unit will beep three times as confirmation. Monitoring of the period

since the last air filter change is now restarted.

13 Cleaning

WARNING

► Switch off the power to the ventilation unit before cleaning.

► When cleaning, make sure that no moisture penetrates into the inside of the

housing.

► Never use a high pressure cleaner, steam cleaner or steam jet.

The ventilation unit is made of high quality plastic and requires little care.

► Wipe the outer surfaces from time to time with a soft, damp cloth. Use mild soapy

water. A commercially available plastic cleaner can be used for particularly stubborn

dirt.

NOTICE

► Never use acidic, corrosive or abrasive cleaning agents.

Maintenance of the M-WRG-II series of units is described in separate maintenance

instructions (in preparation).

«
...
38
39
40
41
42
...
»

Содержание M-WRG-II E-F





























































Отзывы:

Нет отзывов

Похожие инструкции для M-WRG-II E-F

Бренд: Swegon Страницы: 2

Бренд: Hunter Страницы: 2

NOVENCO NovAx ACN SMOKE

Бренд: Schako Страницы: 8

MERCURY ST E Series

Бренд: Ferroli Страницы: 36

Бренд: Kasanova Страницы: 32

Бренд: KDK Страницы: 12

Бренд: ARDES Страницы: 40

Бренд: Heylo Страницы: 18

Бренд: ebm-papst Страницы: 14

Air Purifier 195ECM

Бренд: Lifebreath Страницы: 1

Бренд: Progress Lighting Страницы: 54

comfort SC-SF111B01

Бренд: Scarlett Страницы: 12

Бренд: Harbor Breeze Страницы: 19

Бренд: Delta Страницы: 4

Бренд: DAYRON Страницы: 61

Бренд: Fancom Страницы: 83

Бренд: Premier Страницы: 11

Бренд: Casablanca Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды