Meltem M-WRG-II E-F Скачать руководство пользователя страница 23

Страница: 23 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 23 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

Controls and indicators

The ventilation units from the M-WRG-II P-T and M-WRG-II E-T series can be operated

both via the membrane touch pad on the unit and via the InControl pushbutton sensor or

three-step rotary switch.

NOTICE

The optional wireless remote control M-WRG-FBH, part no. 5478-10, is used to control,

program and extend the range of functions of all M-WRG-II units. The functionality of

the individual buttons on the membrane touch pad, the InControl pushbutton sensor or

three-step rotary switch can thus be adapted to suit the customer’s requirements. You

will find more details in the user guide “Wireless remote control M-WRG-FBH” (see

section 1.12 on page 11).

7.1

Controls and indicators on the ventilation unit

On the left of the ventilation unit there is a membrane touch pad with 5 buttons (items 1 to

5 in Fig. 12). These buttons are used to set the ventilation levels / programs. The 5 LEDs

(LEDs 1 to 5 in Fig. 12) indicate the status of the ventilation unit. They also display any

fault messages or whether an air filter needs to be changed.
The mains switch (item 1 in Fig. 13) is located behind the unit cover. The unit cover must

be removed in order to access it.

Fig. 12: Membrane touch pad and LEDs on the left

of the unit

LED 1

LED 2

LED 3

LED 4

LED 5

Fig. 13: Mains switch, visible when unit cover is

removed

Содержание M-WRG-II E-F





























































Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды

Meltem M-WRG-II E-F, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание M-WRG-II E-F

Отзывы:

Похожие инструкции для M-WRG-II E-F

Бренды по названию

Популярные бренды