Meltem 710000 Скачать руководство пользователя страница 38

Страница: 38 / 44

- 38 -

Installation manual

M-WRG-II M

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

9.14

Aligning the wall box on the outside before plastering

►

Fill the gaps between the wall box and wall aperture all around and continuously with

expanding foam or using another suitable filling material.

9.14.1 If the wall is less than 36.5 cm thick

► Use a Styrofoam saw to cut off the excess wall box (item 1 in Fig. 34 and Fig. 35) and

filler piece, if necessary (item 2 in Fig. 35), so that they are flush with the wall or any

attached insulation.

NOTICE

The wall box fixes the ventilation pipes with a 2° fall to the external wall.

► If the unplastered wall is thin (24 cm or less), do not cut off the wall box flush with

the unplastered wall. Allow the wall box to protrude into the external thermal insula-

tion composite system (ETICS) as this is the only way to allow the ventilation pipes

to pass far enough through and so be fixed in place.

► When fitting the ETICS, make sure that the ventilation pipes maintain their 2° fall.

9.14.2 If the wall is more than 36.5 cm thick

►

Compensate for thicker walls with continuous pipes. For walls that are 63 cm

thick or more, you will need 100 cm long outdoor and exhaust air pipes

(M-WRG-LR 100, part no. 5580).

NOTICE

The pipes must be continuous. Pipes that have been joined must not be used as there

is a risk of allowing condensation to penetrate into the wall area.

Fig. 34: Aligning the wall box

without

filler piece

Fig. 35: Aligning the wall box

with

filler piece

Содержание 710000













































Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды

Meltem 710000, Руководство по установке

Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды