Meltem 710000 Скачать руководство пользователя страница 34

Страница: 34 / 44

- 34 -

Installation manual

M-WRG-II M

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

9.10

Joining flexible pipe connectors and cutting flexible pipes to length (only

when connecting a flexible pipe system)

►

Loosen the two cross-head screws

(item 1 in Fig. 29) and lift up the bar

catch (item 2 in Fig. 29).

► Remove the flat ductwork bend

(item 3 in Fig. 29) from the ductwork

connection adapter (item 4 in

Fig. 29).

►

Remove the red protective cover

(item 5 in Fig. 29) from the flex

ible pipe adapter (item 6 in Fig. 29)

M-WRG-FRA75 (part no. 5056-00/75)

or M-WRG/FRA63 (part no.

5056-00/63).

► Insert the fitting adapter

M-WRG-FSA lang, part no. 5375-00

(item 7 in Fig. 29) into the flat

ductwork bend (item 3 in Fig. 29).

NOTICE

Make sure that you insert the fitting

adapter so that the short side points up

(see item 7 in Fig. 29).

► Attach the flexible pipe adapter

(item 6 in Fig. 29) to the fitting

adapter (item 7 in Fig. 29) and seal the join with a layer of sealing tape 30 mm wide.

► Insert the assembled flexible pipe connectors (items 3, 6 and 7 in Fig. 29) into the

ductwork connection adapter (item 4 in Fig. 29) to test the fit.

► Shorten the flexible pipes (item 8 in Fig. 29) so that they can be inserted into the flex

ible pipe adapter (item 6 in Fig. 29).

Fig. 29:

Joining flexible pipe connectors and cutting

flexible pipes to length

Содержание 710000













































Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды

Meltem 710000, Руководство по установке

Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды