Meltem 710000 Скачать руководство пользователя страница 10

Страница: 10 / 44

- 10 -

Installation manual

M-WRG-II M

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

Planning notes

3.1

Requirements for the installation wall

The installation kit can be installed in frame constructions with walls that are at least

24 cm thick (including internal plaster, external render and insulation).

►

For wall structures that are 63 cm thick or more, you will need 100 cm long outdoor

and exhaust air pipes (M-WRG-LR 100, part no. 5580).

NOTICE

The installation kit fixes the ventilation pipes with a 2° fall to the external wall.

—

The installation kit can be shortened by up to 165 mm (to no less than 200 mm).

Allow the kit to protrude into the external thermal insulation composite system

(ETICS) as this is the only way to allow the ventilation pipes to pass far enough

through and so be fixed in place.

—

When fitting the ETICS, make sure that the ventilation pipes maintain their 2° fall.

3.2

Positioning the ventilation unit indoors

Fig. 4: Minimum distances and options for positioning the M-WRG-II M installation kit,

dimensions in millimetres

min. 50

min. 150

without

ductwork connection

min. 300

with

ductwork connection

min. 50 (*)

(*) If a condensate connection (see section 9.12 on page 36) is used, the minimum dimensions must be

adapted to suit the local conditions. This applies, in particular, if condensate is drained inwards, e.g. via a

greywater outlet.

The ventilation unit must be installed indoors in a perpendicular position on an external

wall.

—

The flush-mount installation (wall box) kit must be installed so that the openings for

extract air and supply air point up.

—

For a standard room height of 2.50 m, the best effect for air exchange is achieved if

the top edge of the unit with the supply and extract air openings is roughly 300 mm

below the ceiling.

—

A 110 x 54 mm flat ductwork system or a 75 or 63 mm flexible pipe system can be

connected using the optional ductwork connection adapter M-WRG-II AD-UP. You will

Содержание 710000













































Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды

Meltem 710000, Руководство по установке

Результаты поиска

Содержание 710000

Отзывы:

Похожие инструкции для 710000

Бренды по названию

Популярные бренды