INSTRUCTION MANUAL
54
2.1. Installation
Cut the work area, as per the measurements indicated in figure 1.
The hob should be installed on a completely flat surface to avoid the risk of breaking the glass.
Any reinforcements in the installation area must be removed.
Insert the hob into the opening in the furniture such that it is centralised.
To prevent seepage, apply the supplied sealant around the entire edge of the hob, ensuring that the ends touch
without overlapping (see figure 2).
Do not use silicone to seal the hob, as this will make it impossible to remove if maintenance is required in the future.
Fix the hob in place with the supplied clamps.
Bolts should be tightened sufficiently to fix the hob in place (see figure 3).
The hob should be installed at a minimum distance of 50 mm from the rear wall and 100 mm from side walls.
If any furniture is suspended above the work area, it must be at minimum height of 600 mm above the hob.
If there is a piece of furniture higher than the hob, it must be at a minimum distance of 300 mm away.
Combustible materials, such as curtains, should be at a minimum distance of 500 mm away.
If the hob is installed above a drawer, there must be a division between the base of the hob and the drawer to
avoid accidental contact with the hot base of the hob.
As a minimum, the hob must be installed at a height of 60 mm above the division or the oven installed immediately
below it (see figure 4).
Ventilation
You must provide for the ventilation spaces indicated in figure 4, in particular, a hot air outlet at least 10mm in height
in front and across the width of the plate and a fresh air inlet at the rear.
Both the fresh air inlet and the hot air outlet are essential for proper and efficient functioning of induction hob, extend
life and prevent damage to property.
2.2. Electrical Connection
The appliance must be connected to the power supply by a technically qualified person in accordance with current
safety standards.
Before turning the hob on, make sure that the electrical connections and protection devices are suitable for the
appliance's technical characteristics.
Before making the electrical connection check that the domestic power supply and the limiting device support the
appliance load (see appliance rating plate).
If the hob is installed above an oven, the electrical connections of the two appliances must be made separately,
both to facilitate their extraction and for electrical safety reasons.
To connect the hob to the power supply, it is necessary to install a multiple-pole switch between the appliance and
the network with a 3 mm minimum gap between the contacts, appropriate for the load and according to the safety
standards.
The earth conductor, identified by the green / yellow colour, should not be interrupted by the switch.
The appliances are equipped with a power cord and are designed to operate with a frequency of 550/60 Hz.
According to the models, refer to the tables of technical features, the power supply can be single-phase, two-phase
or three-phase.
The appropriate power cord, single-phase HO5VV F-type and three-phase HO5RR - F
The power supply cable must be positioned such that none of its points can reach a temperature in excess of 50°C
above room temperature.
Also ensure that the supply system is provided with effective grounding according to safety standards, and that
the multiple-pole switch is available with the installed hob.
2
USE AND OPERATION
Содержание MI 1301
