background image

5.5 Photocoupler input

Page 11

The setting 5 k

 may be necessary if the generator has a high output impedance (see specications of manufac-

turer). The driver software shows a bar chart for evaluation of the signal level at the receiver input. The following

detail of the placeplan of TCR511PCI shows the possible jumper setting with the related input impedance:

No jumper set: 5K Ohm

Jumper in this Position: 50 Ohm

Jumper in this Position: 600 Ohm

5.5 Photocoupler input

Pulse width modulated (DC Level Shift) codes are insulated by an onboard photocoupler. The connection scheme

is shown below:

R = 220 Ohm

DIP 2

DIP 1

 Pin 6
DSUB

 Pin 7
DSUB

+ DCLS in

-  DCLS in

The internal series resistance allows direct connection of input signals with a maximum high level of +12 V (TTL

or RS-422 for example). If signals with a higher amplitude are used, an additional external series resistance must

be applied for not exceeding the limit of the forward current of the imput diode (50 mA). The forward current

should not be limited to a value of less than 10 mA to ensure save switching of the photocoupler.

5.6 Configuration of TCR511PCI

The selection of the IRIG code, conguration of the serial interface and a possible oset of the received IRIG time

to UTC must be set up by the monitor software via the PCIExpress bus. In contrast to AFNOR NFS 87-500 the

IRIG telegram containes only the day of year (1...366) instead of a complete date. To ensure correct function

of TCR511PCI, the date stored in the realtime clock of the board must be set when using IRIG codes therefore.

This setting can be done by a terminal software also.

If the time zone of the received IRIG code is not UTC,

the local oset to UTC must be congured to ensure

correct function of the driver software. If the local time

zone is MEZ for example, the board must be set to a

local oset of `+60min' (MEZ = UTC + 1 h).

The serial interface COM0 can be congured to send a time telegram with reference to UTC or to the received

local IRIG time.

TCR511PCI

Date: 2009-06-24

11

Содержание TCR511PCI





















Отзывы: