Megger DELTA4000 Скачать руководство пользователя | Manualshive

Страница: 36 / 74

background image

M

AVTMDELTA4000-EN Rev 6 April 2018

28

Operation

Test Mode

DELTA 4000 offers a quick setting for available test modes.

The top line (UST-R in this case) defines and describes the selected test mode.

The second and third lines explain how the instrument is configured for the

measurement. They have a different designation depending on if UST

(Ungrounded Specimen Test) or GST (Grounded Specimen Test) measurements

are conducted.

UST mode

Ground and Guard are internally connected. Red and Blue terminals are either

internally connected to be measured or internally connected to Ground (and
Guard). In UST mode, the center line refers to the terminal or terminals that are

measured and the lower line refers to the terminal that is internally connected to

Ground and therefore excluded from the measurement.

GST mode

The current returning from Ground is measured. The Red and Blue terminals are

either connected to Ground to be included in measurement or Guard to be
excluded from the measurement.

«
...
34
35
36
37
38
...
»

Содержание DELTA4000











































































Отзывы:

Нет отзывов

Похожие инструкции для DELTA4000

Бренд: FagronLab Страницы: 16

Бренд: XM Fitness Страницы: 10

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Unitary products group Страницы: 28

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: quadient Страницы: 14

Бренд: Qu-Bit Electronix Страницы: 31

Бренд: Yamaha Страницы: 45

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

MultiFill 003-561-005

Бренд: Hanskamp Страницы: 20

Бренд: Rigol Страницы: 12

Бренд: Gaspardo Страницы: 176

Бренд: laerdal Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды