Meech A60008 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

background image

12

6. Installation

All Meech Coldstream Guns are fitted with a strong magnet allowing it to be fitted to

any surface that will hold the magnet.

The magnet can be removed by unscrewing the hot end silencer and removing the nut
holding the magnet in place.

Air Fitting

The large Coldstream Gun has a ¼” BSP female air fitting.

The small Coldstream Gun has a 1/8” BSP female air fitting.

Standard Pneumatic push-fit compressed air fittings can be used on the Coldstream

Gun.

«
...
10
11
12
13
14
...
»

Содержание A60008





















Отзывы:

Нет отзывов

Похожие инструкции для A60008

Бренд: Laser Страницы: 2

Бренд: Grizzly Страницы: 44

Бренд: Sealey Страницы: 3

Бренд: Chicago Pneumatic Страницы: 32

Бренд: PowerBox Systems Страницы: 30

Бренд: GEM Страницы: 2

Бренд: INIM Страницы: 4

Protege PRT-PSU-DIN-8A

Бренд: ICT Страницы: 36

Бренд: Laguna Tools Страницы: 23

Бренд: TE Connectivity Страницы: 8

Бренд: Tripp Lite Страницы: 3

Бренд: Ubermann Страницы: 40

Бренд: SharpX Страницы: 16

Бренд: RED ROOSTER Страницы: 8

Бренд: Delta Electronika Страницы: 6

Бренд: SNOWJOE Страницы: 20

Бренд: Laguna Tools Страницы: 28

Бренд: AKUA Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды