Chapter 3 - Powering on the Mediatrix 3300
IP Address Discovery or Configuration
18
Mediatrix 3300 – Analog Gateway
To start the Mediatrix 3300 with a dynamic IP address:
1.
If you need to discover the IP address of the Mediatrix 3300, install and start your network packet
sniffer.
2.
Power on the Mediatrix 3300 by flipping the power switch. If this is the very first time you are
installing the Mediatrix 3300, it will restart twice.
3.
Power on the PCs.
Your computers do not have to be turned on for the telephone or fax services.
You can now access the Mediatrix 3300 web interface. Refer to the
Software Configuration Guide
for more details.
Initial Provisioning Sequence
When starting the Mediatrix 3300 for the first time, it needs to be configured before it can support calls. This
process is known as
provisioning
. This sequence assumes that you have installed the Mediatrix 3300
hardware as per
“Hardware Installation” on page 14
The Mediatrix 3300 requests its configuration only on the first restart. You can change the configuration at will
after the initial provisioning and the provisioning system can refresh the Mediatrix 3300 configuration.
Initial provisioning sequence:
1.
When the Mediatrix 3300 starts, it broadcasts a message requesting DHCP services (if the unit is
configured to start in DHCP mode).
2.
The DHCP server responds with a set of WAN IP addresses and network parameters, one of which
is the Mediatrix 3300 WAN IP address.
The following are some of the network parameters assigned via DHCP:
•
Mediatrix 3300 WAN IP address
•
Subnet Mask
•
Default Router IP address
•
DNS IP addresses
•
Configuration script server IP address and port number (optional)
•
SIP Servers IP address and port number
3.
The Mediatrix 3300 request its configuration by using a configuration file.
Default Static WAN IPv4 Address Configuration
If there is no DHCP server in your network, then the WAN IP address has to be configured statically.
To start the Mediatrix 3300 with a static WAN IP address:
1.
Power on the Mediatrix 3300 by flipping the power switch. If this is the very first time you are
installing the Mediatrix 3300, it will restart twice.
2.
Reconfigure the IP address of your computer to
192.168.0.11
and the Subnet Mask to
255.255.255.0
. Restart the computer.
3.
Power on the PCs.
Your computers do not have to be turned on for the telephone or fax services.
4.
Insert a small, unbent paper clip into the
RESET/DEFAULT
hole located at the rear of the Mediatrix
3300.
The
Power
LED will start blinking, and after a few seconds, all the LEDS will start blinking. Release
the paper clip after all the LEDs start blinking and before they all stop blinking (between 7-11
seconds).
This procedure is called a partial reset. After a partial reset is performed, the Mediatrix 3300 uses
the default WAN IP address 192.168.0.1/24. Refer to
for details on the
partial reset procedure.
Содержание Mediatrix 3308
