Mecademic Meca500 R3 Скачать руководство пользователя страница 35

Страница: 35 / 110

Programming manual for Meca500 (for firmware 9.2.x)

TCP/IP COMMUNICATION

default values

By default, the gripper closed and open states are those detected during the homing of the gripper, i.e.,

closed

= 0 and

open

≤ 6, in the case of the MEGP 25E gripper, or

open

≤ 48, in the case of the MEGP 25LS

gripper. To go back to these default values, use

SetGripperRange

(0,0).

2.1.24 SetGripperVel

(

)

This command limits the velocity of the gripper fingers (with respect to the gripper).

Arguments

•

: percentage of maximum finger velocity (~100 mm/s), ranging from 5% to 100%.

default values

By default, the finger velocity limit is 50%.

2.1.25 SetJointAcc

(

)

This command limits the acceleration of the joints during movements resulting from joint- space

commands (see

Figure 11

). Note that this command makes the robot stop, even if blending is enabled.

Arguments

•

: percentage of maximum acceleration of the joints, ranging from 0.001% to 150%.

default values

The default joint acceleration limit is 100%.
Note that the argument of this command is exceptionally limited to 150. This is because in firmware 8,

a scaling was applied so that if this argument is kept at 100, most joint- space movements are feasible

even at full payload. More precisely, if you are upgrading from firmware 7 and you want to keep the

same joint accelerations, you need to multiply the arguments of your

SetJointAcc

commands by the

factor 1.43.

2.1.26 SetJointVel

(

)

This command limits the angular velocities of the robot joints. It affects the movements generated by

the

MovePose

and

MoveJoints

commands.

Arguments

•

: percentage of maximum joint velocities, ranging from 0.001% to 100%.

default values

By default, the limit is set to 25%.

It is not possible to limit the velocity of only one joint. With this command, the maximum velocities of all

joints are limited proportionally. The maximum velocity of each joint will be reduced to a percentage

its top velocity. The top velocity of joints 1 and 2 is 150°/s, of joint 3 is 180°/s, of joints 4 and 5 is 300°/s,

and of joint 6 is 500°/s.

Содержание Meca500 R3















































































































Результаты поиска

Содержание Meca500 R3

Отзывы:

Похожие инструкции для Meca500 R3

Бренды по названию

Популярные бренды

Mecademic Meca500 R3, Руководство по программированию

Результаты поиска

Содержание Meca500 R3

Отзывы:

Похожие инструкции для Meca500 R3

Бренды по названию

Популярные бренды