Measuretek PS-103-180 Скачать руководство пользователя страница 10

 
 

PS

103

 

www.measuretek.net

 

.

 

8

 

.

 

 
 

Serial Communication (continued) 

Meaning of  Some Symbols: 
 

0¯ ¯ ¯ ¯ 

Zero point is over the setting range

0_ _ _ _ 

Zero is below the setting range

Ad¯ ¯ ¯ 

Analog digital converter chip over max. range

Ad _ _ _ 

Analog digital converter chip below min. range

¯ ¯ ¯ ¯ ¯ 

Weight signal is too large 

_ _ _ _ 

Weight signal is too small 

EEP.E1 

Config parameters incorrect (no set, no calibration, over normal range, etc.)

EEP.E2 

User parameters incorrect 

CAL-Px 

Calibration point 

CAL.Er 

Error in calibration 

CAP.-- 

The setting full capacity will be displayed

Cx.y 

No. x configuration parameter is set to y

Ux.y 

No. x user parameter is set to y

Lo.bAt 

Battery voltage is below 3.6V 

 
 
 
 

Replacement Parts 

Part Number 

Description 

MH12R97601G 

AC120V/DC6V 500mA UL adaptor

 

 
 
 
 
 

One Year Limited Warranty 

MeasureTek products covered in this manual are guaranteed to be free from defects in material and workmanship for a period of  
one year after date of purchase. Misuse, accidental damage, overload, alteration, and improper installation are expressly excluded.  
Any product which is determined to be defective in material or workmanship within this time period may, as the exclusive remedy, be 
returned to an authorized MeasureTek distributor or service center, freight prepaid with prior return authorization, to be repaired or 
replaced at the manufacturer’s option.    MeasureTek’s liability under this warranty is limited to the repair or replacement of the 
defective product and in no event shall MeasureTek be liable for consequential or indirect damages. 
 

Содержание PS-103-180











Отзывы: