background image

6

 

Preface 

About this User’s Guide 

What you will learn from this user's guide 

This user's guide describes the Measurement Computing 

CIO-DDA06/Jr/16 

data acquisition 

board

 

and lists 

hardware

 specifications. 

Conventions in this user's guide 

For more information 

Text presented in a box signifies additional information related to the subject matter. 

Caution!

 

Shaded caution statements present information to help you avoid injuring yourself and others, 
damaging your hardware, or losing your data. 

bold

 text 

Bold 

text is used for the names of objects on a screen, such as buttons, text boxes, and check boxes. 

italic

 text 

Italic

 text is used for the names of manuals and help topic titles, and to emphasize a word or phrase. 

Where to find more information 

Additional information about 

CIO-DDA06/Jr/16 

hardware is available on our website at 

www.mccdaq.com

. You can also contact Measurement Computing Corporation with specific questions.  

Knowledgebase: 

kb.mccdaq.com

Tech support form: 

www.mccdaq.com/support/support_form.aspx

Email: 

[email protected]

Phone: 508-946-5100 and follow the instructions for reaching Tech Support

For international customers, contact your local distributor. Refer to the International Distributors section on our 
website at 

www.mccdaq.com/International

Содержание USB-3100 Series



























Отзывы: