manualshive.com logo in svg

Measurement Computing USB-1208HS, Руководство пользователя

Поделиться
Скачать
Measurement Computing USB-1208HS Скачать руководство пользователя страница 9

 

9 

Chapter 3 

Functional Details 

Analog input acquisition modes 

The USB-1208HS can acquire analog input data in two basic modes – software paced and hardware paced. 

Software paced mode 

You can acquire one analog sample at a time in software paced mode. You initiate the A/D conversion by 
calling a software command. The analog value is converted to digital data and returned to the computer. You 
can repeat this procedure until you have the total number of samples that you want. 

The throughput sample rate in software paced mode is system-dependent, and can range from 33 S/s to 
4000 S/s. 

Hardware paced mode 

You can acquire data from up to eight channels in hardware-paced mode. The analog data is continuously 
acquired, converted to digital values, and written to an onboard FIFO buffer on the USB-1208HS until you stop 
the scan. The FIFO buffer is serviced in blocks as the data is transferred from the USB-1208HS FIFO buffer to 
the memory buffer on your computer. 

The maximum sample rate is 1 MS/s aggregate over one-to-eight channels. You can start a continuous scan with 
either a software command or with an external hardware trigger event. 

External components 

The USB-1208HS has the following external components, as shown in Figure 2. 

 

Screw terminals 

 

LED indicators 

 

USB connector 

 

1 

Screw terminal pins 1 to 28 

4 

Activity LED 

2 

Screw terminal pins 29 to 56 

5 

USB connector 

3 

Status LED 

 

 

Figure 2. External components 

 

Содержание USB-1208HS

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды