manualshive.com logo in svg

Measurement Computing TC-32, Руководство пользователя

Поделиться
Скачать
Measurement Computing TC-32 Скачать руководство пользователя страница 19

TC-32 User's Guide 

Specifications 

19 

Note 2:  

When thermocouple sensors are connected to different common mode voltages, the channels with 
floating thermocouples sensors will be biased to approximately the average value of the applied 
common mode voltages. Each of the applied common mode voltages must then be less than or equal to 
the average common mode voltage ±1.40 V or [CMV

applied

 

≤ (CMV

average

 ±1.4 V)]. 

Note 3:  

Measurement sensitivity is the smallest change in temperature that can be detected. 

Channel configuration 

Table 2. Channel configuration specification 

Sensor Category 

Condition 

Specification 

Thermocouple 

J, K, S, R, B, E, T, N 

32 differential channels 

Note 4:  

Channel configuration is stored on EEPROM external to the isolated microcontroller by the firmware 
whenever any item is modified. Modification is performed by commands issued from an external 
application, and the configuration is made non-volatile through the use of the EEPROM. 

Compatible thermocouple sensors 

Table 3. Compatible sensor type specifications 

Parameter 

Specification 

Thermocouple 

J: –210 °C to 1200 °C 

K: –270 °C to 1372 °C 

R: –50 °C to 1768 °C 

S: –50 °C to 1768 °C 

T: –270 °C to 400 °C 

N: –270 °C to 1300 °C 

E: –270 °C to 1000 °C 

B: 0 °C to 1820 °C 

Accuracy 

Thermocouple measurement accuracy 

Table 4. Thermocouple accuracy specifications, including CJC measurement error. All specifications are (±). 

Sensor 
Type 

Sensor 
Temperature 
(°C) 

Accuracy Error 
Maximum (°C),  
15°C to 35°C 

Accuracy Error 
Typical (°C),  
15°C to 35°C 

Accuracy Error 
Maximum (°C),  
0°C to 45°C 

Accuracy Error 
Typical (°C),  
0°C to 45°C 

J 

–210 

1.965 

0.910 

2.167 

0.989 

0  

0.787 

0.361 

0.816 

0.375 

1200 

0.752 

0.371 

1.148 

0.508 

K 

–210 

2.295 

1.061 

2.520 

1.152 

0 

0.821 

0.376 

0.852 

0.392 

1372  

1.029 

0.504 

1.560 

0.688 

S 

–50 

2.467 

1.111 

2.655 

1.223 

250 

1.835 

0.825 

1.961 

0.904 

1768 

0.893 

0.361 

1.519 

0.590 

R 

–50 

2.609 

1.174 

2.810 

1.293 

250  

1.862 

0.837 

1.992 

0.918 

1768 

0.754 

0.305 

1.346 

0.520 

B 

250 

2.450 

1.090 

2.707 

1.254 

700 

0.937 

0.424 

1.136 

0.520 

1820 

0.610 

0.300 

1.056 

0.467 

E 

–200 

1.754 

0.811 

1.933 

0.880 

0 

0.775 

0.355 

0.806 

0.369 

1000 

0.657 

0.323 

0.989 

0.437 

Distributed by MicroDAQ.com, Ltd.               www.MicroDAQ.com               (603) 746-5524

Содержание TC-32




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды