Measurement Computing DPG Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 15

Measurement Computing DPG Series Скачать руководство пользователя страница 4

Instruction Manual

DPG-Series Inclinometer

MEAS Deutschland GmbH

www.meas-spec.com

phone: +49-(0)231-9740-0

Hauert 13, D-44227 Dortmund, Germany

4 of 15

fax: +49-(0)231-9740-20

July 2015

3.1 Notice

Please observe all proper safety rules and regulations for electrical devices
when installing this inclinometer. In addition, the following recommendations are
made.

1. Do not apply power to the inclinometer during installation.

2. Avoid applying any mechanical pressure or stress to the housing.

3. Do not operate an inclinometer beyond the maximum angular sensing range
or threshold. Irreparable damage may occur.

4. Do not exceed the maximum fastening torque for the mounting screws,
as the base plate may become warped and/or irreparably damaged.

5. Use detergents free of solvents or acid for cleaning of the housing.

6. Avoid direct solar radiation.

7. Recommended tightening torque of cable gland (3±0.5 Nm) should be
checked once in a year after purchase to secure IP class of sensor module.

8. Should the inclinometer fail to operate properly, consult this manual for
possible solutions. Do not attempt to open the inclinometer, as damage may
occur. For other troubleshooting measures, please contact our service team.

«
...
2
3
4
5
6
...
»

Содержание DPG Series
















Отзывы:

Нет отзывов