3. Connection of Dimming Functions
4. NTC Connection
5. Recommended Screwdriver, Wire and Torque Setting
6. Suggested Maximum Number of the LCM Units that can be Connected to a MCB (miniature circuit breaker) at 230Vac
a. 0-10Vdc or 10V PWM (non-DA version only)
c. Push dim (DA version only)
d. Synchronization operation
The lights
LCM units (slaves) can be dimmed synchronously through a LCM unit (the master) directly controlled via
driven by
0-10Vdc, 10V PWM, DALI or push dim dimming function. The wiring is shown as below.
Note: ONLY use open push button witho ut indicator light.
Warning:
Risk of short circuit. The push button can only be linked between the PUSH and the AC/L (brown or black).
DO NOT connect the push button to the AC/N (blue or white).
b. DALI (DA version only)
Note : Maximum DALI cable length is 300m
(based on a 1.5mm or 14AWG cable)
2
DA+
DA-
DALI
controller
Dimming control mechanism
Function
Turn ON/OFF
Dim UP/DOWN
Reset
None
Pushing time
0.1 ~ 1 sec
1.5 ~ 10 sec
> 11 sec
< 0.05 sec
SYN.
+
-
+
-
SYN.
+
-
+
-
SYN.
+
-
+
-
Master
Slave 1
Slave 2
‧
‧
‧
Mating housing for SYN. connectors : JST B2B-XH or equivalent
Maximum number of the LCM units : 10 (1 9 slaves)
Maximum cable length between each units : 20m (based on a cable with cross-section of 0.15mm ~0.3mm or AWG No. of 22 ~ 26)
2
2
Note 1 : DO NOT connect dimming circuitry to slaves.
Note 2 : Please make sure all units are set to 100% dimming setting (factory default) before synchronizing.
Note: These calculated values are based on MCB S201 series manufactured by ABB.
http://www.meanwell.com
Type
Model
B10
B16
C10
C16
LCM-40(DA)
10
16
17
28
LCM-60(DA)
9
15
16
26
Solid wire
Stranded wire
American wire gauge
Wire stripping length
Screwdriver
Recommended tightening torque
Suggested push-down strength
-----
-----
-----
-----
6mm Phillips
4.6 kgf-cm (4 lb-in)
-----
The cover
(the blue one)
Push terminal
(ACL/N, PUSH, DA , Vo )
±
±
ψ
ψ
1.024 - 1.628mm
0.823 - 2.08mm
2
14 - 18AWG
10mm (0.39")
3mm Phillips
-----
3 - 4 kp (6.61-8.81 lb )
F
‧
‧
It will always dim up when light intensity is lower than 10%, whereas it will
Factory dimming setting: 100%
always dim down when light intensity is higher than 90%
DIM-
DIM+
0~10VDC
+
-
NTC-
NTC+
AC/L
AC/N
Push Button
PUSH
LIVE (Brown or black)
NEUTRAL (Blue or white)
ψ
ψ
0.404 - 0.643mm
0.12 9 - 0.3 26mm
2
22 - 26AWG
7mm (0.27 ")
3mm Phillips
2.88 kgf-cm (2.5 lb-in)
-----
Screw terminal
(FAN , NTC , DIM )
±
±
±
