MDT Technologies SCN-RT2UP.01 Скачать руководство пользователя страница 23

Страница: 23 / 57

Technical Manual Temperature Controller

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49

-2263-4588

• [email protected] • www.mdt.de

4.4.2 Operating modes & Setpoints

The following settings are available at the ETS-Software:

Figure 8: Operating modes & setpoints

The chart shows the dynamic range of the operating modes and setpoints:
ETS-text

Dynamic range

[default value]

comment

Basis comfort setpoint

18,0°C

–

25,0°C

[21,0°C]

The basis comfort setpoint is the reference
point of the control.

Night reduction

Lowering in K

0 K

–

10,0 K

[3,0 K]

Lowering of the temperature by choosing
the operating mode night.
Relative to the basis comfort setpoint.

Standby reduction

Lowering in K

0 K

–

10,0 K

[2,0 K]

gets activated when no other operating
mode was chosen
The lowering is relative to the basis
comfort setpoint.

Setpoint frost protection

3°C

–

12°C

[7°C]

Setpoint of the operating mode frost
protection.
indicated by an absolute value

Setpoint heat protection

24°C

–

40°C

[35°C]

Setpoint of the operating mode heat
protection.
indicated by an absolute value

Table 12: Operating modes & setpoints

Содержание SCN-RT2UP.01


























































Результаты поиска

Содержание SCN-RT2UP.01

Отзывы:

Похожие инструкции для SCN-RT2UP.01

Бренды по названию

Популярные бренды

MDT Technologies SCN-RT2UP.01, Руководство пользователя

Результаты поиска

Содержание SCN-RT2UP.01

Отзывы:

Похожие инструкции для SCN-RT2UP.01

Бренды по названию

Популярные бренды