MDT Technologies SCN-IP000.03 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

20

20

4 Settings – IP-Router

The settings of the application "IP Router

without Secure

" and "IP Router

with Secure

" differ. Both

settings are described below.

4.1 Settings IP Router with Secure

4.1.1 General

The following parameters can be set in the submenu "General":

Figure 10: General Settings – IP Router

The table below shows the settings for this submenu:
ETS-Text

Dynamic Range

[Default value]

Comment

Enable slow connections



yes



no

Adjust the timeout for tunneling
connections. By default, slow
connections are not supported
and a short timeout is used for
the UDP connection. This can be
increased by supporting slow
connections which may be
necessary especially for tunnel
connections over the internet.

Manual Function



disabled



pass all telegrams



pass all physical telegrams



pass all group telegrams

Defines the behavior after
manual changeover

Switch-off time for
Manual Function



10 min



1 hour



4 hours



8 hours

Setting of the automatic release
time from manual mode to
automatic mode

«
...
18
19
20
21
22
...
»

Содержание SCN-IP000.03


























































Отзывы:

Нет отзывов

Похожие инструкции для SCN-IP000.03

Бренд: Paradyne Страницы: 20

Compshere 3000 Series

Бренд: Paradyne Страницы: 2

Бренд: Pantech Страницы: 17

Бренд: Watchguard Страницы: 24

Бренд: Salto Страницы: 2

Бренд: Campbell Страницы: 38

StorageWorks AIT 35GB AutoLoader

Бренд: Compaq Страницы: 4

Бренд: Patton electronics Страницы: 12

Бренд: EMCIS Страницы: 14

Бренд: Quantum Страницы: 7

DiamondLink 3201

Бренд: Patton Страницы: 12

Ezi-SERVOII EtherCAT TO

Бренд: Fastech Страницы: 108

Бренд: Global411 Страницы: 15

Бренд: Comet Labs Страницы: 11

Бренд: Airlinkplus Страницы: 20

Бренд: Comtrend Corporation Страницы: 4

Бренд: Linksys Страницы: 6

Бренд: MaxComm Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды