background image

FIG. 12

Lock Pin

10

FIG. 12

This device complies with the part 15 of the FCC rules.

Operation is subject to the following two conditions :

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may 

cause undesired operation.

#16

SOUND
ON/OFF

POWER
ON/OFF

ELECTRONIC SCORER OPERATION

1. Unscrew bolt using a screwdriver and open the battery box. Insert 4 AA 

batteries ( not included) in the order of polarity as shown on the inside 

cover. Then close the cover using a screwdriver. Turn the power on using 

the on/off switch. (if the game will not be used for a long period of the time, 

we recommend that the batteries should be removed).

2. Sound ON/OFF – use this switch while the game is on to turn the sound 

OFF and ON.

3. While game is in Sleep Mode, if a basketball is scored, the game will turn back on and the score 

board will begin the 5 sec. countdown.

4.After finishing the game, Turn OFF the scorer by using the ON/OFF switch. NOTE: The scoreboard 

will turn off after 5 minutes, if not in use, however, we recommend turning the ON/OFF switch to 

OFF when the game will not be used for an extended period of time.

21.  Folding position when not in use the basketball game and insert the Lock Pin (#33) as shown in FIG 12. 

      NOTE: The lock pin (#33) needs to be removed from its original position when the game is being used before 

insertion to the new position when folded. 

IMPORTANT NOTICE!

Make sure to use the Lock 

Pins (#33) to secure the Ball 

Return with Side Netting in 

place.

Содержание 57001






















Отзывы: