McQuay MicroTech II N2 Скачать руководство пользователя страница 3

IM 730-0

3

Limited Warranty 

Consult your local McQuay Representative for warranty details. Refer to Form 933-43285Y. To find
your local McQuay Representative, go to 

www.mcquay.com

.

Revision History

IM 732

August 1, 2002

Initial Release

Reference Documents 

Number

Source

Title

OM748

www.McQuay.com

Air Source Heat Pump with Electric Heat (Software Model 00)

OM749

www.McQuay.com

Water Source Heat Pump with Electric Heat (Software Model 02)
Water Source Heat Pump without Electric Heat (Software Model 03)

OM750

www.McQuay.com

DX Cooling with Electric Heat (Software Model 04)

OM751

www.McQuay.com

DX Cooling Only (Software Model 05)

OM752

www.McQuay.com

Electric Heat Only (Software Model 06)

OM753

www.McQuay.com

DX Cooling with Wet Heat - Valve Control (Software Model 07)
DX Cooling with Wet Heat - F&BP Damper Control (Software Model 08)

OM754

www.McQuay.com

2-pipe Wet Heat Only - Valve Control (Software Model 09)
2-pipe Wet Heat Only - F&BP Damper Control (Software Model 10)

OM755

www.McQuay.com

2-pipe Heat/Cool - Valve Control (Software Model 11)
2-pipe Heat/Cool - F&BP Damper Control (Software Model 12)

OM756

www.McQuay.com

4-pipe Heat/Cool - Valve Control (Software Model 13)
4-pipe Heat/Cool - F&BP Damper Control (Software Model 14)

OM757

www.McQuay.com

2-pipe Cooling Only - Valve Control (Software Model 15)
2-pipe Cooling Only - F&BP Damper Control (Software Model 16)

OM758

www.McQuay.com

2-pipe Cooling with Electric Heat - Valve Control (Software Model 17)
2-pipe Cooling with Electric Heat - F&BP Damper Control (Software Model 18)

ED 15069

www.McQuay.com

MicroTech II™ Unit Ventilator Unit Controller
Protocol Implementation Conformance Statement

ED 15065

www.McQuay.com

MicroTech II™ AAF®-HermanNelson® Unit Ventilator Unit Controller Protocol
Information

IM731

www.McQuay.com

MicroTech II™ AAF®HermanNelson® Unit Ventilator Controller BACnet®
Communication modules

IM747

www.McQuay.com

MicroTech II™ Unit Ventilator Unit Controls Installation Manual

www.johnsoncontrols.com/Metasys/n2open.htm

N2 -- A Data Communication Protocol for Building Automation and
Control Networks

Notice

Copyright © 2002 McQuay International, Minneapolis MN All rights reserved throughout the world
 ™ The following are trademarks or registered trademarks of their respective companies: N2 Open from Johnson Controls
Corporation, Protocol Selectability, MicroTech II, and AAF-HermanNelson from McQuay International.

Содержание MicroTech II N2













Отзывы: