background image

18

Power Output

Minimum sine wave continuous average power output 

per channel, all channels operating is:

250 watts into a 8 ohm load

300 watts into a 4 ohm load

Output Load Impedance

8 and 4 ohms 

Rated Power Band

20Hz to 20,000Hz

Total Harmonic Distortion

0.025% maximum harmonic distortion at any power 

level from 250 milliwatts to rated power, 20Hz to 

20,000Hz

Dynamic Headroom

2.5dB, 8 ohm load

3.5dB, 4 ohm load

Frequency Response

+0, -0.9dB from 20Hz to 20,000Hz

Input Sensitivity for rated output (8 ohm load)

5.0 Volt Balanced

2.5 Volt Unbalanced

Input Sensitivity for rated output (4 ohm load)

3.8 Volt Balanced

1.9 Volt Unbalanced

Signal To Noise Ratio (A-Weighted)

83dB (100dB below rated output)

Intermodulation Distortion

0.1% maximum, if the instantaneous peak power 

output does not exceed the rated power output for any 

combination of frequencies from 20Hz to 20,000Hz.

Wide Band Damping Factor

Greater than 85, 8 ohm Load

Greater than 45, 4 ohm Load

Input Impedance

32,000 ohms Balanced

18,000 ohms Unbalanced

Voltage Gain

25dB

Power Control Input

5-15VDC, less than 1mA

Power Control Output

12VDC, 50mA maximum total

Power Requirements

100 - 240Volts, 50/60Hz at 10 Amps

Standby: less than 0.5 watt

Overall Dimensions

Width is 17-1/2 inches (44.5cm)

Width with Side Mount Brackets attached is

               19 inches (48.3cm)

Height is 4-5/16 inches (11.0cm) including feet

Depth is 21 inches (53.3cm) including the Front Panel 

and Cables

Weight

23.5 pounds (10.7 kg) net, 39.9 pounds (18.1 kg) in 

shipping carton

Shipping Carton Dimensions

Width is 26-1/2 inches (67.3cm)

Height is 11-3/4 inches (29.9cm)

Depth is 24-1/4 inches (61.6cm)

Specifications

Specifications

Содержание MI254





















Отзывы: