background image

 
 

 

 

Knowing your MR18 

Fuel Cap

 

To remove the filler cap, turn it counterclockwise. To replace the filler cap, turn it clockwise until it is 
snugly held in the tank. 

 

Adjusting the Steering Wheel 

 

To change the tilt of the steering column, pull on the grey lever located at the top of the steering column 
and adjust the angle to your comfort. The steering wheel can also telescope in and out by turning the 
quick release lever on the left-hand side of the column and pulling the steering column to the desired 
position. It can be telescoped by 4 inches. 

Rigid Display 

 

The MR18 is equipped with a DP-720 rigid display from Danfoss. This display is equipped with a touch 
screen as well as buttons to navigate between pages.  It will display the diagnostics of the tractor while 
in use. 

Warning 

 

Fuel sprays can happen where there is pressure in the fuel tank and the fuel cap is 
removed too quickly. When removing the fuel cap, loosen the cap slightly and wait for 
any hissing to stop and then remove it.

 

Vapor from the fuel could be ignited by sparks or flames, causing serious burns and 
injuries. Before refueling, stop the engine. Always keep sparks and flames away from 
the filler neck.

 

Содержание utrac MR18































Отзывы: