background image

8

NOTE:

Do not clean filter in gasoline or other

flammable solvent to avoid creating a fire haz-

ard or producing harmful evaporative emis-

sions.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Replace parts.

Air Filter Cover

Air Filter

Button

REPLACE SPARK PLUG

Replace the spark plug each year to ensure

the engine starts easier and runs better. Set

spark plug gap at 0,6 mm. Ignition timing is

fixed and nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and dis-

card.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 19 mm

socket wrench.

4. Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

Pre--wound spools offer the most convenient

method for replacing line and ensuring opti-

mum performance.

S

Replacement spools are color--coded to

ensure use of the correct spool with your

unit. Be sure to use the same color spool as

the existing spool.

NOTE:

Always clear dirt and debris from

cutting head components when performing

any type of maintenance.

S

Hold spool and unscrew cap by turning in

the direction shown on top of the cap.

S

Remove line guide ring and spool.

Cap

Spool

Line guide ring

Use a pre--wound spool or refill spool with

line. If using a pre--wound spool, remove tape

strip from line and spool.

REFILLING THE SPOOL WITH LINE

WARNING:

Use only 2 mm diameter

round line. Other sizes and shapes of line will

not advance properly and will result in improp-

er cutting head function or can cause serious

injury. Do not use other materials such as

wire, string, rope, etc. Wire can break off dur-

ing cutting and become a dangerous missile

that can cause serious injury.

1. Cut a length of 8 meters of 2 mm diameter

round McCulloch

®

brand line.

Feed line in

direction

shown on

spool.

Spool

2. Insert one end of line into center cavity of

empty spool. Ensure line will feed into

spool in the direction shown on the spool

(counterclockwise).

3. Continue feeding line into spool, leaving

10 -- 15 cm unwound from center of spool.

INSTALLING SPOOL WITH LINE

1. Install replacement spool.

2. Thread line through line guide ring.

Line through guide ring

Replacement Spool

Slot

3. Rest guide ring on spool and place line

through slot. Allow line to extend 10 -- 15

cm from center of spool.

4. Ensure line remains in slot while screwing

cap on to the shaft.

Only tighten cap

hand tight!

Содержание Twist 'N Edge














Отзывы: