background image

-- 4 --

WHAT IS WHAT?

1. Throttle Lever

8. Blower tube

2. Primer button

9. Elbow tube

3. Choke lever

10. Vacuum bag

4. Fuel cap

11. Lower vacuum tube

5. Starter rope

12. Upper vacuum tube

6. Rear handle

13. Instruction manual

7. Spark plug

WHAT IS WHAT?

1

2

3

4

5

6

7

8

9

10

11

12

13

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following
list.

S

Blower

S

Blower tube

S

Upper vacuum tube

S

Lower vacuum tube

S

Elbow tube

S

Vacuum bag

NOTE:

It is normal for the fuel filter to rattle

in the empty fuel tank.

ASSEMBLY

WARNING:

Stop engine and be sure

the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.

WARNING:

If received assembled,

repeat all steps to ensure your unit is properly
assembled and all fasteners are secure. Fol-
low all safety information in the manual and on
the unit.

D

A standard screwdriver is required for as-
sembly.

BLOWER TUBE ASSEMBLY

1. Align the rib on the blower tube with the

groove in the blower outlet; slide the tube
into place.

NOTE:

Knob must be loose enough to allow

blower tube to be inserted in blower outlet.
Loosen knob by turning counterclockwise.

Blower
Tube

Blower
Outlet

Rib

Groove

2. Secure the tube by turning the knob clock-

wise.

3. To remove the tube, turn the knob counter-

clockwise to loosen the tube; remove the
tube.

VACUUM BAG ASSEMBLY

1. Open the zipper on the vacuum bag and

insert the elbow tube.

2. Push the small end of the elbow tube

through the small opening in the bag.

Содержание BVM 250












Отзывы: