McCulloch 115377027 Скачать руководство пользователя страница 18

Страница: 18 / 20

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message

labeled

IMPORTANT

regarding the use of

gasohol in your chain saw. Fuel stabilizer is

an acceptable alternative in minimizing the

formation of fuel gum deposits during stor-

age. Add stabilizer to the gasoline in the fuel

tank or fuel storage container. Follow the mix

instructions found on stabilizer containers.

Run engine at least 5 minutes after adding

stabilizer.

HELPFUL TIP

During storage of your gas/

oil mixture, the oil will sepa-

rate from the gas.

We recommend that you

shake the gas can weekly

to insure proper blending of

the gas and oil.

ENGINE

Remove spark plug and pour 1 teaspoon

of 40:1, 2-cycle engine oil (air cooled)

through the spark plug opening. Slowly

pull the starter rope 8 to 10 times to distrib-

ute oil.

Replace spark plug with new one of rec-

ommended type and heat range.

Clean air filter.

Check entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

At the beginning of the next season, use

only fresh fuel having the proper gasoline

to oil ratio.

OTHER

Do not store gasoline from one season to

another.

Replace your gasoline can if it starts to

rust.

TROUBLE

CAUSE

REMEDY

Engine will not

start or will run

only a few

seconds after

starting.

1. Ignition switch off.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

1. Move ignition switch to ON.

2. See “Difficult Starting” in

Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

Engine will

not idle

properly.

1. Idle speed requires

adjustment.

2. Carburetor requires

adjustment.

1. See “Carburetor Adjustment” in the

Service and Adjustments Section.

2. Contact an authorized service dealer.

1. Air filter dirty.

2. Spark plug fouled.

3. Chain brake engaged.

4. Carburetor requires

adjustment.

Engine will not

accelerate,

lacks power,

or dies under

a load.

1. Clean or replace air filter.

2. Clean or replace plug and regap.

3. Disengage chain brake.

4. Contact an authorized service dealer.

Engine

smokes

excessively.

1. Too much oil mixed with

gasoline.

1. Empty fuel tank and refill with

correct fuel mixture.

WARNING:

Always stop unit and disconnect spark plug before performing all of

the recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

Chain moves

at idle speed.

1. Idle speed requires

adjustment.

2. Clutch requires repair.

1. See “Carburetor Adjustment” in the

Service and Adjustments Section.

2. Contact an authorized service dealer.

Содержание 115377027





















Результаты поиска

Содержание 115377027

Отзывы:

Бренды по названию

Популярные бренды

McCulloch 115377027, Инструкция по эксплуатации

Результаты поиска

Содержание 115377027

Отзывы:

Бренды по названию

Популярные бренды