McCrometer FlowConnect Скачать руководство пользователя страница 17

Страница: 17 / 19

published technical data and instructions are subject to change without notice. Contact your McCrometer representative for current

technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078 Printed In The U.S.A. Lit. # 30122-40 Rev. 1.0 / 3-1-17

Page 17 of 19

™

FlowConnect

STEP 2: Cycle through the first menu level

The first level menu selection appear in the order

shown in the table at right.

a. Pass the wand over the P until you reach the L1

-Go to menu selection (Figure 20).
If you pass it by, the menu selections will start

again from the beginning.

First Menu Level

Display

Menu Title

Description

Loc-CodE

Program Lock Out

Enter w/ preset code

rAtE-Un

Rate Unit/Time

Sets Unit/Time

rAtE-dP

Rate Format

Sets Rate Decimal Place

tot-Un

Totalizer Unit

Sets Unit

tot-dP-E

Totalizer Decimal Point

Enable

Enables/Disables

Totalizer Decimal Point

tot-dP

Totalizer Decimal Place

Sets Decimal Place

Tot-FAct

Totalizer Multiplier

Sets Multiplier

20mA-Un

20mA Unit

Sets 20mA Unit

20mA-dP

20mA DP

Sets 20mA Decimal Place

20mA-FS

20mA FS

20mA Full Scale

PLS-Un

Pulse Unit

Sets Pulse Unit

PLS-dP

Pulse Decimal Place

Sets Pulse Decimal Place

PLS-Inc

Pulse Increment

Sets Pulse Value

CAL-Pct

Calibration Percent

Adjusts Meter Accuracy

-Go to

Go to Second Menu

Level or Run

* These menu items are controlled by the tot-dP-E setting.

Depending on its setting, either tot-dP or Tot-FAct will

appear, but not both.

Figure 20.

b. Pass the wand over the

once. The selection

will advance to L2 -Go to (Figure 21).

Figure 21.

c. Pass the wand over the P once to advance to

the second menu level. The selection PAr-S

with the meter’s serial number will appear

(Figure 22). This is the first item in the second

menu level.

Figure 22.

*
*



 



 







 



 







 



 





Содержание FlowConnect




















Результаты поиска

Содержание FlowConnect

Отзывы:

Бренды по названию

Популярные бренды

McCrometer FlowConnect, Инструкция по модернизации

Результаты поиска

Содержание FlowConnect

Отзывы:

Бренды по названию

Популярные бренды