manualshive.com logo in svg

McCrometer FlowConnect, Инструкция по модернизации

Поделиться
Скачать
McCrometer FlowConnect Скачать руководство пользователя страница 15

Copyright © 2016 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. Any 

published technical data and instructions are subject to change without notice. Contact your McCrometer representative for current 

technical data and instructions.

www.mccrometer.com

3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA

TEL: 951-652-6811 • 800-220-2279 • FAX: 951-652-3078        Printed In The U.S.A.        Lit. # 30122-40 Rev. 1.0 / 3-1-17

Page 15 of 19

™

FlowConnect

4 - Setting the New FlowCom Register

Brief explanation of why this is necessary:

After a FlowCom unit has been replaced with a new FlowConnect unit, users may want to set the register with the total 

gallons amount from the previous register. The instructions below are a concise guide to programming and resetting 

the total gallons only.

See the FlowCom IOM for complete procedures and description of FlowCom programming and features.

RECOVERY FROM ERROR

It is possible to make a wrong selection when programming the FlowCom 

register. If this happens, you can recover from the error by doing the 

following:

Cycle through the menu selections

• 

If you remember the original value, cycle through all of the values 

until you come to the selection you want.

Time out the programming mode

• 

If you can’t find the value you want or find the menu you need, allow 

the programming mode to time itself out. This is done by making no 

selections or changes  while the digital display is still flashing and 

waiting about 30 - 60 seconds.

What this procedure will help 
you do:

As shown by the example at right 

(Figure 15), you will be able to change 

the total on the register that appears 

during normal operation.

This procedure will show you how 
to change the total from 

0

 to 

12345

.

FROM

TO

Figure 15. Example register totals

    

   

    

       

    

   

    

       

It is very important that each step is followed carefully! If you do not feel confident programming the 

FlowCom register, we strongly recommend contacting a service technician.
While these instructions are streamlined for just the programming function required, if you find you 

made an error in and cannot back out of the menus, follow the “RECOVERY FROM ERROR” procedure. 

WARNING!

i

Содержание FlowConnect




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды