McConnel M402G Скачать руководство пользователя страница 8

 

THIS MANUAL MUST BE HANDED TO THE CUSTOMER  

BEFORE THE MACHINE IS USED FOR THE FIRST TIME 

 

 
 

 

 
 
 
 
 
 
 
 
 

 
 
 
 

 

McCONNEL LIMITED 

TEMESIDE WORKS 

LUDLOW 

SHROPSHIRE 

SY8 1ND 

 

TELEPHONE: 

 01584 873131 

 

 
 
 
 
 
 
 
 
 
 

All dimensions and capacities mentioned in this book are approximate.  In pursuance of the 
Companies policy of constant development, the right is reserved to depart, without notice, 
from  any  detail  illustrated  or  specified  in  this  book,  without  incurring  the  obligation  to 
provide such modifications on machines previously delivered. 
 
 
No  responsibility  will  be  accepted  by  McConnel  Limited  for  any  injury,  damage  or  loss 
arising from the improper use or lack of maintenance of any machinery supplied by them 
or  from  any  failure  of  the  user  to  comply  with  all  instructions  published  by  Tractor  or 
Loader manufacturers, particularly with regard to maximum load capacities, tyre pressures 
and stability, or with instructions and regulations pertaining to Tractor Cabs.

 

 
 

Содержание M402G



























Отзывы: