background image

Page 16 

 

 

S Series – S1400/800 Operating Instructions 

 

 

 

 

 

 

Performance Of Your Amplifier:  Specifications 
 

Main Specifications  
 

Parameter (Units) 

S1400 

S800 

Output Power per channel [Crest Factor = 4.8] (Watts) 

 

 

8 Ohms 

775 

475 

4 Ohms 

1500 

950 

2 Ohms 

1800 

1550 

Output Power per channel bridged [Crest Factor = 4.8] (Watts)

 

 

 

8 Ohms 

3000 

1900 

4 Ohms 

3600 

3100 

THD+N, 4 Ohms (%) 

 

 

@1kHz, 1dB below max output power  

<

 

0.008 

0.007 

@20Hz - 20kHz, 1dB below max output power 

<

 

0.03 

0.03 

Gain Options (dB) 

32 / 36 

32 / 36 

Sensitivity Options for max power (dBu) 

8.0 / 4.0 

5.5 / 1.5 

Sensitivity Options for max power (Volts) 

2.0 / 1.2 

1.4 / 0.9 

Frequency Response, +0/0.5dB (Hz) 

20 — 20000 

20 — 20000 

Power Consumption, Nominal @ 240V, 4 Ohms (A) 

3.2 

2.1 

Power Consumption, Nominal @ 120V, 4 Ohms (A) 

6.4 

4.2 

Dimensions H x W x D (mm) 

 

 

Amplifier 

88 x 482 x 428 

88 x 482 x 428 

Boxed 

230 x 580 x 560 

230 x 580 x 560 

Boxed Shipping — all except UK 

250 x 610 x 600 

250 x 610 x 600 

Weight (kgs) 

 

 

Amplifier 

23.25 

20.5 

Boxed — shipping 

25 

22.25 

 
Additional Specifications 
 

Parameter (Units) 

S1400 

S800 

Input Impedance — Active Balanced (Ohms) 

20k 

20k 

Input CMRR (dB) 

 

 > 

60 

60 

SNR (dB) 

106 

106 

Damping Factor, 1kHz, 8 ohms 

400 

400 

Signal Limiters Present 

Yes 

Yes 

Protection Present — Short Circuit / DC Output / Temperature 

Yes 

Yes 

Mains In-rush Control Present 

Yes 

Yes 

Output Power per channel, 8 Ohms (Watts) 

 

 

Sine Wave @ 1kHz 

650 

450 

Continuous music [Crest Factor of 2.8 or 9dB] 

725 

475 

Continuous music [Crest Factor of 4.8 or 14dB] 

775 

475 

Continuous music [Crest Factor of 7.8 or 18dB] 

775 

500 

Output Power per channel, 4 Ohms (Watts) 

 

 

Sine Wave @ 1kHz 

1250 

800 

Continuous music [Crest Factor of 2.8 or 9dB] 

1450 

900 

Continuous music [Crest Factor of 4.8 or 14dB] 

1500 

950 

Continuous music [Crest Factor of 7.8 or 18dB] 

1500 

1000 

Output Power per channel, 2 Ohms (Watts) 

 

 

Sine Wave @ 1kHz 

1300* 

1300 

Continuous music with Crest Factor of 2.8 [9dB] 

1675 

1500 

Continuous music with Crest Factor of 4.8 [14dB] 

1800 

1550 

Continuous music with Crest Factor of 7.8 [18dB] 

1900 

1700 

 
Due to continuing product improvement the above specifications are subject to change. 
*Power output is automatically limited to this value on the S1400 model. 

Содержание S1400


















Отзывы: