MC2 Audio Delta 100 Скачать руководство пользователя страница 20

Page 20           

Delta Series – Non-DSP Models Operating Instructions 

 

 

 

 

 

 

Performance Of Your Amplifier:  Specifications 

 
Main Specifications  
 

Parameter (Units) 

Delta 40

Delta 80

Delta 100 

Delta 120

Output Power per channel [Crest Factor = 4.8] (Watts) 

 

 

 

 

8 Ohms

540 

975 

1500 

2400 

4 Ohms

1000 

1800 

2800 

4800 

2.7 

Ohms

1200 2300 3700 6200 

Output Power per channel bridged [Crest Factor = 4.8] 
(Watts)

 

 

 

 

 

8 Ohms

2000 

4000 

5600 

--- 

 

 

 

 

THD+N, 4 Ohms (%) 

 

 

 

 

@1kHz, 1dB below max output power  

<

0.08 0.08 0.08 0.08 

@20Hz - 20kHz, 1dB below max output power 

<

0.1 0.1 0.1 0.1 

Gain Options (dB) 

26/32 

26/32 

26/32 

26/32 

Sensitivity Options for max power (dBu) 

6.23 

8.79 

10.7 

13 

Sensitivity Options for max power (Volts) 

1.59 

2.13 

2.66 

3.48 

Frequency Response, +0/0.5dB (Hz) 

20 — 20000 

20 — 20000 

20 — 20000 

20 — 20000 

Power Consumption, Nominal @ 240V, 4 Ohms (A) 

2.9 

5.0 

7.5 

6.4 

Power Consumption, Nominal @ 120V, 4 Ohms (A) 

10.4 

15.5 

13.2 

Dimensions H x W x D (mm) 

 

 

 

 

Amplifier

88 x 482 x 

428 

88 x 482 x 

428 

88 x 482 x 

428 

88 x 482 x 

428 

Boxed

230 x 580 x 

560 

230 x 580 x 

560 

230 x 580 x 

560 

230 x 580 x 

560 

Boxed Shipping — all except UK

250 x 610 x 

600 

250 x 610 x 

600 

250 x 610 x 

600 

250 x 610 x 

600 

Weight 

(kgs) 

    

Amplifier

10.0 11.0 12.5 12.25 

Boxed — shipping

12.0 

13.0 

14.5 

14.25 

 
Additional Specifications 
 

Parameter (Units) 

Delta 40

Delta 80

Delta 100 

Delta 120

Input Impedance — Active Balanced (Ohms) 

20k 

20k 

20k 

20k 

Input CMRR (dB) 

60 

60 

60 

60 

Damping Factor, 1kHz, 8 ohms 

400 

400 

400 

400 

Signal 

Limiters 

Present 

Yes Yes Yes Yes 

Protection Present — Short Circuit / DC Output / 
Temperature 

Yes Yes Yes Yes 

Mains In-rush Control Present 

Yes 

Yes 

Yes 

Yes 

Output Power per channel, 8 Ohms (Watts) 

 

 

 

 

Continuous music [Crest Factor of 2.8 or 9dB] 

525 

950 

1460 

2350 

Continuous music [Crest Factor of 4.8 or 14dB]

540 

975 

1500 

2400 

Continuous music [Crest Factor of 7.8 or 18dB]

555 

1000 

1540 

2450 

Output Power per channel, 4 Ohms (Watts)

 

 

 

 

Continuous music [Crest Factor of 2.8 or 9dB] 

970 

1850 

2720 

4700 

Continuous music [Crest Factor of 4.8 or 14dB]

1000 

1900 

2800 

4800 

Continuous music [Crest Factor of 7.8 or 18dB]

1030 

1950 

2880 

4900 

Output Power per channel, 2.7 Ohms (Watts)

 

 

 

 

Continuous music with Crest Factor of 2.8 [9dB] 

1170 

2050 

3600 

6000 

Continuous music with Crest Factor of 4.8 [14dB]

1200 

2100 

3700 

6200 

Continuous music with Crest Factor of 7.8 [18dB]

1230 

2150 

3880 

6300 

 

 

 

 

 
Due to continuing product improvement, the above specifications are subject to change. 

Содержание Delta 100
























Отзывы: