These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau/
Germany.
These operating instructions reflect the current technical specifications at time of print. We reserve the right to change
the technical or physical specifications.
©
2007 by Conrad Electronic SE. Printed in Germany.
Operating Instructions
Version 07/07
PAR 56 Set, short
Polished aluminium
Item no.: 58 12 55
black
Item no.: 58 12 56
This product complies with the applicable National and European specifications.
Intended Use
The PAR56 Set, short, is used for lighting and for generating lighting effects on dance floors, in party basements, on stages,
etc.
It is approved only for connection to 230 V~/50 Hz wall outlets with a protective conductor. Do not use any other source of
energy.
It can only be used in closed rooms, and therefore not outdoors. Contact with moisture must be avoided at all times.
Any use other than that described above could lead to damage to this product and involves the risk of short circuits, fire,
electric shock, etc.
No part of the product can be modified or rebuilt.
The safety instructions must be observed at all times.
Symbols
This symbol on the device indicates that the user should read these operating instructions prior to using
the product.
The flash icon in a triangle is used to alert you to potential personal injury hazards such as electric
shock.
An exclamation mark indicates important notes in these operating instructions that should always be
observed.
The F symbol indicates that the device is suitable for direct attachment on normally flammable surfaces.
This symbol indicates the minimum distance to the illuminated surface.
Safety instructions
The warranty will lapse for damage due to non-compliance with these operating instructions. We will not
assume liability for any resulting damage.
We shall not accept liability for damage to property or personal injury caused by incorrect handling or
non-compliance with the safety instructions. The warranty is voided in these cases.
• Prior to commissioning, check the device for damage. If the device is damaged, it may not be put into operation.
• For safety and licensing (CE) reasons, unauthorised conversion and/or modifications to the product are not permitted.
• The PAR56 Set is designed according to protection class I. For this reason, the device’s mains plug must be connected
with a mains socket with earthing contact.
• Do not look straight into the light source during operation. The light rays could lead to brief sight problems. They can
furthermore possibly cause epileptic fits. Of course, this applies particularly for epileptics.
• Check the device and the power cable from time to time for damage.
• Never replace a damaged connecting cable yourself. If the connecting cable is damaged, take the device to a specialist
workshop to be repaired.
• Avoid heavy mechanical stress on the PAR56 Set and do not expose it to high temperatures, strong vibration or dripping
or spray water.
• Never pour out any liquids above the device. You run the risk of causing a fire or a fatal electric shock. If any liquid should
nevertheless penetrate the device, immediately disconnect it from the power supply network and contact a specialist.
• Keep the unit out of the reach of children. Do not let the lamp be used by children or persons who do not possess sufficient
knowledge of such devices.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material for children.
• On industrial sites the accident prevention regulations of the association of the industrial workers’ society for electrical
equipment and utilities must be followed.
• If the device is used in commercial institutions or in public, the user must ensure that installation and connection to the
power supply network meet the safety regulations and that this is checked by an expert.
• If you are not sure about the correct connection or if questions arise which are not covered by the operating instructions,
please do not hesitate to contact our technical support or another specialist.
Mounting
The assembly and installation of the device may only be carried out by an accordingly qualified
specialist.
When carrying out installation or service works, make sure that the area below the installation site is
blocked.
Never install the product in the vicinity of combustible or easily inflammable materials, (e.g. curtains,
decorative material etc.)! Keep a free space of at least 50 cm around the device for unhindered air
circulation.
The housing must not come into contact with any other surfaces or objects at all.
Please make sure the appliance is sufficiently ventilated (never cover it!).
The surface or illuminated objects must be at least 1.5 m away from the light’s point of exit.
The maximum permissible environmental temperature of 40°C may not be exceeded.
The installation surface or mounting fixture needs to be designed in a way, that it can take 10 times its
load capacity for at least 1 hour without damaging deformation.
It is essential that the device is furthermore secured by a second safety suspension (eg safety catch)
which is independent from the actual installation fixture. If the main supports fail, no part of the
installation should be able to fall down.
Make sure that the device cannot swing freely when installing it.
The PAR56 Set must not be installed within reach of persons or above the place where people are
present.
• Fasten the lamp housing by means of the mounting clamp on the wall, ceiling or a suitable crossbeam. Only use suitable
installation material.
• Align the lamp housing as desired and tighten the screw of the clamp carefully.
• If required, insert suitable coloured film in the coloured film frame and fasten this in the holder at the light’s point of exit.
Inserting / Replacing the illuminant
The lamp must be replaced if it is damaged or has been deformed due to heating.
Disconnect the device from the power supply prior to illuminant replacement (pull the power plug out
of the power outlet!).
Only use suitable lamps (see „Technical Data“).
Do not use lamps with an output that is higher than is specified; this could lead to excessively high
heating of the device.
Let the device cool for ten minutes after disconnecting it from power (acute burning hazard) before
replacing the bulb.
Also observe the instructions of the lamp manufacturer.
• Do not touch the lamp with bare hands; wear protective gloves or use a clean cloth, as oil from the skin significantly
reduces the service life of the bulb.
• Remove the foil frame from its support.
• Press together the lamp clamping ring in front of the casing and remove it.
• If necessary, remove the defective lamp and pull off the socket.
• Plug the socket onto the illuminant contacts of the new illuminant and attach the new illuminant with the lamp clamp ring
in the beamer casing.
• Place the coloured foil frame back in its support.
• Never operate the device until you have reassembled the beamer casing.
Connecting the power supply
Connection to the power supply must always be carried out by a specialist familiar with the hazards
involved and with the regulations for mains connection.
The mains plug has to be connected to a mains socket with earthing contact.
Do not let the mains cable come into contact with other cables.
Do not lay out the connection cables in such a manner that anyone can trip over or get caught in them.
Furthermore, ensure that the power cables cannot be pinched or damaged by sharp edges.
Make sure that the power voltage corresponds to the specifications on the lamp housing.
•
Insert the mains plug into an earthed mains socket.
• The device starts to operate as soon as it is connected to the power supply.
Putting into Operation and Use
Do not operate the light when it is unattended.
Never touch the device when in operation or shortly afterwards as it becomes very hot. There is risk of
burning!
Light effect devices are not suitable for permanent use. The strict keeping to operation pauses
increases the service life of the product significantly.
Do not switch the device on and off at short intervals. Otherwise, the service life of the lamp could be
significantly decreased.
If the device is not in use, disconnect the power plug or press the all-pole switch (with a contact gap of
3 mm) to disconnect the device from any power supply.
• The lamp housing starts to operate as soon as it is connected to the power supply. For this reason, it should be operated
using a light control unit.
• Smoke or odours may be generated the first time that the device is used. This is not a device malfunction.
• If the light control unit is equipped with a lamp preheater, this should be activated so that the service life of the lamp is
increased.
• Set the lamp preheater so that the filament of the bulb glows slightly.
Care and maintenance
Always disconnect the device from the power supply before cleaning it.
The outside of the PAR56 Set should only be cleaned with a soft, dry cloth.
Never use caustic cleaning agents or chemical solutions as the surface of the housing could be damaged.
The interior of the housing should be vacuum cleaned from time to time.
Disposal
When the product is no longer usable, dispose of it in accordance with the applicable statutory regulations.
Technical data
Operating voltage ............................................................................................................................. 230V AC/50 Hz
Illuminant ........................................................................................................................................... PAR 56/300W max.
F
...m
