MB QUART SS100.4, Руководство пользователя

Страница: 6 / 17

SS75.2 / SS125.2 / 2 CHANNEL AMPLIFIER APPLICATIONS
4
FULL RANGE MONO
This is the most basic application for the SUPER SPORT Series 2 channel
amplifiers.
1. Interconnect cable checklist:
Connect the
LINE INPUTS
to the Radio/CD with good quality RCA cables.
2. Crossover Switch:
The
X-OVER
switch must be in the
FULL
position.
3. Crossover frequency control checklist:
N/A for full range operation.
4. Line Level:
Refer to the section “Setting up systems after installation for best performance”.
NOTE: Minimum final loudspeaker impedances:
4 &-2-Ohms stereo mode or 4-Ohms mono mode
This amplifier will not do 1-Ohm stereo or 2/1-Ohm mono operation.
This application illustrates the basic mono bridging method for all Autotek 2
Switch setting checklist:
channel amplifiers.
- The
AMPLIFIER X-OVER
switch must be in the
FULL
position.
Interconnect cable checklist:
Crossover frequency control setting checklist:
A MONO signal source is required, such as would be available from the mono
N/A for full range operation. sub bass output of an active crossover, whether stand alone, or built into a head
TIP: Important:
If you are using the mono sub bass output of an active crossover, there is unit or equalizer. Do not be tempted to connect the hot, or positive
nothing wrong with switching in the low pass filter in these amplifiers for a outputs, from any source together to obtain a mono signal, as this could very
steeper low pass roll-off. well damage the output stage of that source.
It is necessary to feed the SAME signal to both left and right inputs via a Y-
adapter RCA cable. Connect the mono speaker positive terminal to the RIGHT
Minimum final loudspeaker impedance:
+, and its negative terminal to LEFT -.
- 4-Ohms mono.
FULL RANGE STEREO
LIN
E O
UT
L
IN
E IN
PU
T
R
R
L
L
+ -
gn
d -
+
HI I
NP
UT
5V
0
.2V
0
dB
1
2d
B
60
Hz
1
.2K
Hz
3
0H
z 2
50
Hz
LE
VE
L
B
AS
S E
Q
H
PF
L
PF
FU
LL
LP
F H
PF
M
ON
O
ST
ER
EO
X-O
VE
R
M
OD
E
GN
D
RE
M
+1
2V
PO
W
ER
IN
PU
T
F
US
E
SP
EA
KE
R
OU
TP
UT
BR
ID
GE
D
PO
W
ER
PR
OT
EC
T
LE
FT
R
IG
HT
-
+
-
+
FULL RANGE
STEREO LINE INPUT
REMOTE TURN-ON
CHASSIS GROUND
TO B 12 volts VIA FUSE
FULL RANGE
SPEAKERS
LIN
E O
UT
L
IN
E IN
PU
T
R
R
L
L
+ -
gn
d -
+
HI I
NP
UT
5V
0
.2V
0
dB
1
2d
B
60
Hz
1
.2K
Hz
3
0H
z 2
50
Hz
LE
VE
L
B
AS
S E
Q
H
PF
L
PF
FU
LL
LP
F H
PF
M
ON
O
ST
ER
EO
X-O
VE
R
M
OD
E
GN
D
RE
M
+1
2V
PO
W
ER
IN
PU
T
F
US
E
SP
EA
KE
R
OU
TP
UT
BR
ID
GE
D
PO
W
ER
PR
OT
EC
T
FULL RANGE
MONO LINE INPUT
VIA Y-ADAPTER
FROM MONO SOURCE
FULL RANGE
MONO SPEAKER
REMOTE TURN-ON
CHASSIS GROUND
TO B 12 volts VIA FUSE
The
HIGH LEVEL
inputs are used when the radio/CD player does not have RCA cable outputs. You can connect the radio/CD player speaker wires directly
to the amplifier via the high Level Inputs.
GRAY: CH 1 Speaker Input +
BROWN: CH 1 Speaker input -
Black: Chassis Ground
GREEN: CH 2 Speaker Input -
White: CH 2 Speaker Input + ORANGE: CH 3 Speaker Input +
PINK: CH 3 Speaker input -
Black: Chassis Ground
BLUE: CH 4 Speaker Input -
YELLOW: CH 4 Speaker Input +
Use this connector for 2 CH amplifiers Use both connectors for 4 CH amplifiers
LE
FT
R
IG
HT
-
+
-
+