background image

WARRANTY

Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from 
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty 
period. Components that prove to be defective in materials and workmanship under proper installation 
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was 
purchased. A photocopy of the original receipt must accompany the product being returned. The 
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics 

86$ ,QF 7KLV ZDUUDQW\ LV OLPLWHG WR GHIHFWLYH SDUWV DQG VSHFL¿FDOO\ H[FOXGHV DQ\ LQFLGHQWDO RU

consequential damages connected therewith. To view the full warranty, please visit the website.

The information contained within this document is intended to offer some basic guidelines 

for a few of the most common installations. More complex audio systems should be 

installed by a competent professional. Additional installation information available at

www.maxxsonics.com

MBQuart products are designed and engineered in the USA by

www.maxxsonics.com

MBQ NA2 QSG 01 - rev2

Some models include a bass 
remote. Avoid adjusting the bass 
remote while operating vehicle.

 

Remote Level 
Control

C

Содержание MBQR-STG3-2








































Отзывы: