background image

Title

Section

GENERAL INFORMATION

00

ENGINE

01

CONTENTS

Engine
Workshop
Manual
LF
L3

FOREWORD

This manual explains the service points for 
the above-indicated automotive system. 
This manual covers all models with the 
above-indicated automotive system, not any 
one specific model.

In order to do these procedures safely, 
quickly, and correctly, you must first read 
this manual and any other relevant service 
materials carefully.

All the contents of this manual, including 
drawings and specifications, are the latest 
available at the time of printing. 
As modifications affecting repair or 
maintenance occur, relevant information 
supplementary to this volume will be made 
available at Mazda dealers. This manual 
should be kept up-to-date.

Mazda Motor Corporation reserves the right 
to alter the specifications and contents of 
this manual without obligation or advance 
notice. 

All rights reserved. No part of this book may 
be reproduced or used in any form or by any 
means, electronic or mechanical—including 
photocopying and recording and the use of 
any kind of information storage and retrieval 
system—without permission in writing.

Mazda Motor Corporation

HIROSHIMA, JAPAN

©

2005 Mazda Motor Corporation
PRINTED IN U.S.A., AUGUST 2005
Form No. 1866–1U–05H
Part No. 9999–95–LFL3–05

Содержание 2006-2008 RX7 Engine





























































Отзывы: