manualshive.com logo in svg

Maytag MGS5752BD, Сервисная инструкция

Поделиться
Скачать
Maytag MGS5752BD Скачать руководство пользователя страница 14

Testing Procedures 

 

!

WARNING

 

To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, 
unless testing requires power and/or gas. 

14 16026293 

©2005 Maytag Services

  

Component Testing Procedures 

Illustration Component 

Test 

Procedure 

Results 

 

 

Oven light socket 

Test continuity of receptacle terminals....
 
Measure voltage at oven light.................

Indicates continuity with bulb screwed in.
 
120 VAC; see wiring diagram for terminal 
identification. If no voltage is present at 
oven light check wiring. 

 

 

Door plunger switch 

Remove switch from unit and measure 
the following points: 

COM to NO ........................................

 
 
Plunger in continuity, plunger out infinity. 

 

 

Autolatch assembly 

Disconnect wires and test for 
continuity per wiring diagram. 
 
Refer to Parts Manual for correct 
autolatch switch associated with the 
correct manufacturing number. 

See wiring diagram for schematic layout. 
Access assembly by removing right side 
panel. 
 
Common is in neutral position unless 
locking or unlocking autolatch assembly. 

 

 

270° valve 

5 K btu 
9.2 K btu 
12.5 K btu 
16 K btu 

Verify gas is supplied. 
 
Adjust set screw for simmer control. 

 

 

 

Spark 270° switch 

Test for voltage at terminals ..................
 
Disconnect wiring and check for 
continuity in LITE position......................

120 VAC 
 
 
Continuity in LITE position. 

 

 

Spark ignition 
electrode 

Test for resistance of spark lead............
 
Test ignitor to chassis............................

Continuity 
 
No continuity from ignitor to chassis. 

 

 

Top surface burner 

5 K btu 
9.2 K btu 
12.5 K btu 
16 K btu 

Verify gas is supplied.............................
 
Verify burner cap is positioned 
correctly. 

Check for obstructions in burner ports. 

 

 

Top surface burner cap 

Verify cap is positioned correctly ........... Check for obstructions in burner ports. 

 

L

A

B

A1

B1

N

 

Spark module 4 + 0 

Test for voltage at terminals L and N .....
 
Check polarity and ground.....................

120 VAC (tolerance: 102 to 132 VAC) 
 
See wiring diagram 

 

 

Temperature sensor 

Measure resistance ............................... Approximately 1000 

Ω

 at room 

temperature 75° F (23.8° C). 

 

 

Broil burner 

Verify gas is supplied. 
Orifice adjusted for Natural or LP ..........
 
Check for obstructions or 
contamination in ports ...........................

Factory set to Natural Gas.

 

Adjust as necessary. 
Air shutter opening set to .281 to .343. 
 
Replace if punctured or torn. 

 

 

Bake burner 

Verify gas is supplied. 
Orifice adjusted for Natural or LP ..........
 
Check for obstructions or 
contamination in ports ...........................

Factory set to Natural Gas.

 

Adjust as necessary. 
Air shutter opening set to .469 to .531. 
 
Replace if punctured or torn. 

 

Ignitor 

Test for voltage at terminals ..................
Test for amperage in the circuit .............
(Ignitor may glow but not have 
sufficient amperage to open valve.) 

120 VAC. 
3.2 

−

 3.6 Amps. If not, replace. 

 

 

Convection element 

Disconnect wiring to element and 
measure resistance of terminals............
Measure voltage at broil element...........

 
Approximately 30 

Ω

. 

240 VAC. 

Содержание MGS5752BD
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды